Infiniti FX35, FX50 (S51). Manual — part 558
TRANSFER ASSEMBLY
DLN-67
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: ETX13C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
VK50VE : Exploded View
INFOID:0000000005249115
VK50VE : Removal and Installation
INFOID:0000000005249116
REMOVAL
1.
Remove transmission assembly from the vehicle. Refer to
EM-196, "Removal and Installation"
.
2.
Remove transfer air breather hose.
3.
Remove rear engine mounting member and engine mounting insulator with power tool. Refer to
4.
Support transfer assembly with a jack.
5.
Remove transfer mounting bolts with power tool and separate transfer from transmission.
CAUTION:
Secure transfer assembly and transmission assembly to a jack.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing the transfer to the transmission, install the mount-
ing bolts following the standard below, tighten bolts to the specified
torque.
:Transfer to transmission.
:Transmission to transfer.
• When installing transfer air breather hose, make sure there are no pinched or restricted areas on the transfer
air breather hose caused by bending or winding.
1.
Transfer assembly
: Vehicle front
Refer to
JPDIE0128GB
Bolt No.
A
B
C
D
Quantity
4
3
4
2
Bolt length “ L ” mm (in)
75 (2.95)
45 (1.77)
40 (1.57)
30 (1.18)
JPDIE0105ZZ
DLN-68
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: ETX13C]
TRANSFER ASSEMBLY
- Set transfer air breather hose with the paint mark (A) facing
upward.
- Be sure to insert air breather hose (1) of transmission side to air
breather tube until hose end reaches the tube bend R portion.
- Be sure to insert air breather hose (1) of transfer side to air
breather tube (2) until hose end reaches the tube bend R portion.
- Be sure to fix air breather hose in (A) parts of transmission and
transfer.
• After the installation, check the fluid level, fluid leakage and the A/T
positions. Refer to
.
JPDIE0107ZZ
JSDIA0857ZZ
JPDIE0106ZZ
JSDIA0855ZZ
FRONT CASE AND REAR CASE
DLN-69
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
FRONT CASE AND REAR CASE
VQ35HR
VQ35HR : Exploded View
INFOID:0000000005249117
1.
Plug
2.
Drive chain
3.
Front drive shaft rear bearing
4.
Front drive shaft
5.
Front drive shaft front bearing
6.
Sprocket
7.
Needle bearing
8.
Main shaft
9.
Oil pump
10. Spacer
11.
Steel ball
12. Snap ring
13. Snap ring
14. Main shaft bearing
15. Front case
16. Main shaft oil seal
17. Front oil seal
18. Spacer
19. Snap ring
20. Circlip
21. Electric controlled coupling
22. Oil cover
23. O-ring
24. Retainer
25. Transfer fluid temperature sensor
26. Baffle plate
27. Spacer
28. Snap ring
29. Dowel pin
30. Rear case
31. Harness bracket
32. Breather tube
33. Filler plug
34. Gasket
35. Drain plug
36. Rear bearing
37. Snap ring
38. Spacer
39. Rear oil seal
JPDIE0200GB
DLN-70
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: ETX13C]
FRONT CASE AND REAR CASE
VQ35HR : Disassembly
INFOID:0000000005249118
1.
Remove drain plug and filler plug.
2.
Remove harness brackets.
3.
Remove main shaft oil seal from front case.
CAUTION:
Never damage the front case and main shaft.
4.
Remove front oil seal from front case.
CAUTION:
Never damage the front case and front drive shaft.
5.
Remove self-lock nut.
6.
Put a matching mark (A) on the end of main shaft. The mark
should be in line with the mark (B) on the companion flange.
CAUTION:
For the matching mark, use paint. Never damage main
shaft.
7.
Remove companion flange with a puller (A) (commercial service
tool).
CAUTION:
Never damage the companion flange.
8.
Remove rear oil seal from rear case with the puller (A)
[SST:KV381054S0 (J-34286)].
CAUTION:
Never damage the rear case.
9.
Remove spacer from main shaft.
40. Companion flange
41. Self-lock nut
A.
Oil seal lip
B.
Matching surface
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-16, "Recommended Chemical Products and Sealants"
.
: Apply petroleum jelly.
: Apply transfer fluid. Refer to
MA-12, "Fluids and Lubricants"
Refer to
for symbols not described above.
JPDIE0060ZZ
JSDIA0806ZZ
JPDIE0132ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст