Infiniti FX35, FX50 (S51). Manual — part 1255
INT-22
< REMOVAL AND INSTALLATION >
FLOOR TRIM
5.
Remove foot grille (LH/RH). Refer to
VTL-17, "FOOT GRILLE : Removal and Installation"
.
6.
Remove front seat belt floor anchor bolt (LH/RH). Refer to
SB-8, "SEAT BELT BUCKLE : Exploded View"
.
7.
Remove center console assembly. Refer to
IP-22, "Removal and Installation"
8.
Remove rear floor duct 1. Refer to
VTL-19, "REAR FLOOR DUCT 1 : Removal and Installation"
.
9.
Remove instrument lower cover (LH/RH), instrument lower panel (LH/RH) and instrument side finisher
(LH/RH). Refer to
IP-12, "Removal and Installation"
10. Remove yaw rate/side G sensor. Refer to
BRC-136, "Removal and Installation"
11. Remove diagnosis sensor unit. Refer to
SR-25, "Removal and Installation"
.
12. Remove console rear bracket. Refer to
IP-22, "Removal and Installation"
.
13. Remove floor harness mounting clamps.
14. Remove dash side finisher (LH/RH), front and rear kicking plate inner (LH/RH) and center pillar lower gar-
nish (LH/RH). Refer to
INT-17, "Removal and Installation"
.
15. Remove floor trim mounting clips and fixing nuts.
16. Remove floor trim from floor trim fixing clips (A) and remove floor
trim.
INSTALLATION
Install in the reverse order of removal.
JMJIA1560ZZ
HEADLINING
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Exploded View
INFOID:0000000005240801
1.
Headlining assembly
2.
Assist grip
3.
Front roof finisher
4.
Lane camera cover
5.
Sun-visor assembly (RH)
6.
Sun-visor holder
7.
Sun-visor cap
8.
Sun-visor assembly (LH)
9.
Rear monitor assembly
JMJIA2064ZZ
INT-24
< REMOVAL AND INSTALLATION >
HEADLINING
Removal and Installation
INFOID:0000000005240802
REMOVAL
1.
Remove the rear seat cushion. Refer to
SE-94, "Removal and Installation"
2.
Remove the rear seatback. Refer to
SE-94, "Removal and Installation"
.
3.
Remove front seat belt anchor bolt (LH/RH). Refer to
SB-8, "SEAT BELT BUCKLE : Exploded View"
4.
Remove rear seat belt anchor bolt (LH/RH). Refer to
SB-15, "SEAT BELT BUCKLE : Exploded View"
.
5.
Remove front pillar garnish (LH/RH), front kicking plate inner (LH/RH), center pillar lower garnish (LH/RH),
center pillar upper garnish (LH/RH), front body side welt (LH/RH), rear body side welt (LH/RH), rear kick-
ing plate inner (LH/RH). Refer to
INT-17, "Removal and Installation"
.
6.
Remove luggage side lower finisher (LH/RH), luggage side upper finisher (LH/RH). Refer to
7.
Remove the sun-visor (LH).
• Remove sun-visor cap.
• Remove mounting screws.
• Disconnect vanity mirror lamp harness connector (with vanity mirror lamp)
8.
With a remover tool, disengage the driver side front roof finisher
(1) fixing pawls and metal clips, disconnect the harness connec-
tor (A) and then remove the front roof finisher.
9.
Remove the lane camera cover mounting pawls with a remover
tool (A), then remove the lane camera cover (1).
10. Disconnect inside mirror harness connectors.
11. Remove the sun-visor (RH).
• Remove sun-visor cap.
• Remove mounting screws.
• Disconnect vanity mirror lamp harness connector (with vanity mirror lamp)
10. Rear hidden clip
11. Roof insulator
12. Dual lock fastener
13. Roof console assembly
14. Roof console bracket
15. Sunroof module plate
16. Roof console
17. Map lamp assembly
18. Map lamp bulb (LH/RH)
19. Map lamp lens (LH/RH)
20. Personal lamp bracket (LH/RH)
21. Personal lamp bulb (LH/RH)
22. Personal lamp finisher (LH/
RH)
23. Personal lamp lens (LH/RH)
: Clip
: Pawl
: Metal clip
: Vehicle front
: Pawl
: Metal clip
: Vehicle front
JMJIA2073ZZ
: Pawl
JMJIA1567ZZ
HEADLINING
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
12. Remove the passenger side front roof finisher mounting pawls
and metal clips with a remover tool (A), then remove the front
roof finisher (1).
13. Remove assist grips.
• With a small flat-bladed screwdriver (A), press the upper side
mounting assist grip cap (1) and pull up to remove the mount-
ing assist grip cap from assist grip (2).
• Once the mounting assist grip cap (1) is removed, pull out the
assist grip (2) to remove.
14. Disengage the rear monitor finisher fixing clips and pawls with a
remover tool (A), disconnect the harness and then remove the
rear monitor finisher (1). (With rear monitor assembly only)
: Pawl
: Metal clip
JMJIA1564ZZ
JMJIA1379ZZ
JMJIA1380ZZ
JMJIA2300ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст