Infiniti FX35, FX50 (S51). Manual — part 935
EM-40
< REMOVAL AND INSTALLATION >
[VQ35HR]
FUEL INJECTOR AND FUEL TUBE
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000005245138
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
Removal and Installation
INFOID:0000000005245139
REMOVAL
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
• Never drain engine coolant when the engine is hot to avoid the danger of being scalded.
1.
Release fuel pressure. Refer to
.
2.
Disconnect battery cable from the negative terminal. Refer to
.
3.
Remove engine cover with power tool. Refer to
.
4.
Remove air cleaner case and air duct. Refer to
1.
Quick connector cap
2.
Fuel feed hose (with damper)
3.
O-ring
4.
Fuel sub tube
5.
O-ring
6.
Fuel damper cap
7.
Fuel damper
8.
O-ring
9.
Fuel tube
10. Clip
11. O-ring (black)
12. Fuel injector
13. O-ring (green)
A.
Refer to
Refer to
for symbols in the figure.
JPBIA1708GB
FUEL INJECTOR AND FUEL TUBE
EM-41
< REMOVAL AND INSTALLATION >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
5.
Remove intake manifold collector. Refer to
6.
Remove fuel feed hose (with damper) (1) from fuel sub-tube (2)
and remove harness bracket (3).
NOTE:
There is no fuel return route.
CAUTION:
• While hoses are disconnected, plug them to prevent fuel
from draining.
• Never separate damper and hose.
7.
When separating fuel feed hose (with damper) and centralized under-floor piping connection, disconnect
quick connector as per the following:
a.
Remove quick connector cap (2) from quick connector connec-
tion on right member side.
b.
Disconnect fuel feed hose (with damper) (1) from bracket hose
clamp.
c.
Push in retainer tabs (2).
d.
Draw and pull out quick connector (1) straight from centralized
under-floor piping (3).
CAUTION:
• Pull quick connector holding position (A) as shown in the
figure.
• Never pull with lateral force applied. O-ring inside quick
connector may be damaged.
• Prepare container and cloth beforehand as fuel will leak
out.
• Avoid fire and sparks.
• Keep parts away from heat source. Especially, be careful
when welding is performed around them.
• Never expose parts to battery electrolyte or other acids.
• Never bend or twist connection between quick connector and fuel feed hose (with damper) dur-
ing installation/removal.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags, etc. (A) or something similar.
8.
Remove fuel sub tube mounting bolt.
9.
Disconnect harness connector from fuel injector.
: Engine front
JPBIA0032ZZ
JPBIA0254ZZ
JPBIA1854ZZ
JPBIA0135ZZ
EM-42
< REMOVAL AND INSTALLATION >
[VQ35HR]
FUEL INJECTOR AND FUEL TUBE
10. Loosen mounting bolts in reverse order as shown in the figure,
and remove fuel tube and fuel injector assembly.
CAUTION:
Never tilt fuel tube, or remaining fuel in pipes may flow out
from pipes.
11. Remove fuel injector (2) from fuel tube (4) as per the following:
a.
Open and remove clip (1).
b.
Remove fuel injector from fuel tube by pulling straight.
CAUTION:
• Be careful with remaining fuel that may go out from fuel
tube.
• Be careful not to damage injector nozzles during removal.
• Never bump or drop fuel injector.
• Never disassemble fuel injector.
12. Remove fuel sub-tube and fuel damper, if necessary.
INSTALLATION
1.
Install fuel damper (4) as per the following:
a.
Install new O-ring (2) to fuel tube (1) as shown. When handling
new O-ring, be careful of the following caution:
CAUTION:
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign
material.
• When installing O-ring, be careful not to scratch it with
tool or fingernails. Also be careful not to twist or stretch
O-ring. If O-ring was stretched while it was being
attached, never insert it quickly into fuel tube.
• Insert new O-ring straight into fuel tube. Never twist it.
b.
Install spacer (3) to fuel damper.
c.
Insert fuel damper straight into fuel tube.
CAUTION:
• Insert straight, checking sure that the axis is lined up.
• Insert fuel damper at 130 N (13.3 kg, 29.2 lb) or less to pre-
vent damage to the parts.
• Insert fuel damper until (B) is touching (A) of fuel tube.
d.
Tighten bolts evenly in turn.
• After tightening bolts, check that there is no gap between fuel
damper cap (5) and fuel tube.
2.
Install fuel sub-tube.
• When handling new O-rings, be careful of the following caution:
CAUTION:
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
: Engine front
JPBIA0034ZZ
3
: O-ring
A
: Installed condition
B
: Clip mounting groove
JPBIA0036ZZ
JPBIA0316ZZ
FUEL INJECTOR AND FUEL TUBE
EM-43
< REMOVAL AND INSTALLATION >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not
to twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it
quickly into fuel tube.
• Insert new O-ring straight into fuel tube. Never decenter or twist it.
• Insert fuel sub-tube straight into fuel tube.
• Tighten mounting bolts evenly in turn.
• After tightening mounting bolts, check that there is no gap between flange and fuel tube.
3.
Install new O-rings to fuel injector, paying attention to the following.
CAUTION:
• Upper and lower O-ring are different. Be careful not to confuse them.
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly
into fuel tube.
• Insert O-ring straight into fuel injector. Never decenter or twist it.
4.
Install fuel injector to fuel tube as per the following:
a.
Insert clip (3) into clip mounting groove (D) on fuel injector (5).
CAUTION:
• Never reuse clip. Replace it with a new one.
• Be careful to keep clip from interfering with O-ring. If
interference occurs, replace O-ring.
b.
Insert fuel injector into fuel tube (1) with clip attached.
• Insert it while matching it to the axial center.
• Insert fuel injector so that protrusion (A) of fuel tube matches
cutout (B) of clip.
• Check that fuel tube flange (E) is securely fixed in flange fixing
groove (C) on clip.
c.
Check that installation is complete by checking that fuel injector
does not rotate or come off.
• Check that protrusions of fuel injectors are aligned with cut-
outs of clips after installation.
5.
Install fuel tube and fuel injector assembly to intake manifold.
CAUTION:
Be careful not to let tip of injector nozzle come in contact with other parts.
Fuel tube side
: Black
Nozzle side
: Green
2
: O-ring (Black)
4
: O-ring (Green)
JPBIA0037ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст