Infiniti F50. Manual — part 649
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-63
C
D
E
F
G
H
I
J
L
M
A
B
LT
TKWM0408E
LT-64
TURN SIGNAL AND HAZARD WARNING LAMPS
TKWM0409E
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-65
C
D
E
F
G
H
I
J
L
M
A
B
LT
Symptom Chart
EKS000TA
Symptom
Possible cause
Repair Procedure
Turn signal and hazard warning
lamps do not operate.
1. Combination flasher unit
2. Open in combination flasher unit
circuit
1. Check combination flasher unit. Refer to
2. Check wiring to combination flasher unit for open circuit.
Turn signal lamps do not operate
but hazard warning lamps operate.
1. 10A fuse
2. Combination flasher unit
3. Turn signal switch
4. Open in turn signal switch circuit
1. Check 10A fuse [No. 5, located in fuse block (J/B)
NO.1]. Turn ignition switch ON and verify battery posi-
tive voltage is present at terminal 1 of combination
flasher unit.
2. Check combination flasher unit. Refer to
3. Check turn signal switch. Refer to
4. Check harness between combination flasher unit termi-
nal 2 and turn signal switch terminal 1 for open circuit.
Hazard warning lamps do not oper-
ate but turn signal lamps operate.
1. 15A fuse
2. Combination flasher unit
3. Hazard switch
4. Open in hazard switch circuit
5. Grounds M24 and M114
1. Check 15A fuse [No. 22, located in fuse block (J/B)
NO.1]. Verify battery positive voltage is present at termi-
nal 4 of combination flasher unit.
2. Check combination flasher unit. Refer to
3. Check hazard switch.
4. Check harness between combination flasher unit termi-
nal 6 and hazard switch terminal 1 for open circuit.
5. Check grounds M24 and M114.
Front turn signal lamp LH or RH
does not operate.
1. Bulb
2. Grounds E42 and E62
3. Open in front turn signal lamp cir-
cuit
1. Check bulb.
2. Check grounds E42 and E62.
3. Check harness between combination switch and front
turn signal lamp for open circuit.
Rear turn signal lamp LH or RH
does not operate.
1. Bulb
2. Grounds B17 and B57
3. Open in rear turn signal lamp cir-
cuit
1. Check bulb.
2. Check grounds B17 and B57.
3. Check harness between combination switch and rear
turn signal lamp for open circuit.
LH and RH turn indicators do not
operate.
1. Grounds M24 and M114
1. Check grounds M24 and M114.
LH or RH turn indicator does not
operate.
1. Bulb
2. Open in turn indicator circuit
1. Check bulb in combination meter.
2. Check harness between combination flasher unit and
combination meter (turn indicator) for open circuit.
LT-66
TURN SIGNAL AND HAZARD WARNING LAMPS
Electrical Components Inspection
EKS000TB
COMBINATION FLASHER UNIT CHECK
●
Before checking, ensure that bulbs meet specifications.
●
Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
blinks when power is supplied to the circuit.
Bulb Replacement
EKS001AS
FRONT TURN SIGNAL LAMP
Refer to
in “HEADLAMP (USA)”.
REAR TURN SIGNAL LAMP
Refer to
LT-79, "REAR COMBINATION LAMP"
in “PARKING, LICENSE PLATE AND TAIL LAMPS”.
Removal and Installation
EKS000W3
FRONT TURN SIGNAL LAMP
Refer to
LT-34, "Removal and Installation"
in “HEADLAMP (USA)”.
SIDE TURN SIGNAL LAMP
GW-115, "Disassembly and Assembly"
in “GLASSES, WINDOW SYSTEM & MIRRORS (GW)” sec-
tion.
REAR TURN SIGNAL LAMP
Refer to
LT-80, "REAR COMBINATION LAMP"
in “PARKING, LICENSE PLATE AND TAIL LAMPS”.
SKIA0470E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст