Infiniti QX56 (Z62). Manual — part 844
INT-24
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000006220253
FOR SECOND BENCH SEAT
JMJIA4007ZZ
1.
Front floor carpet
2.
Carpet hook
3.
Fixing clip
4.
Footrest
5.
Front floor spacer front
6.
Front floor spacer rear
7.
Floor hook
8.
Rear floor carpet
9.
Dual lock fastener
: Pawl
: Vehicle front
FLOOR TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FOR SECOND CAPTAIN SEAT
FRONT FLOOR CARPET
FRONT FLOOR CARPET : Removal and Installation
INFOID:0000000006220254
REMOVAL
1.
Remove front seat assembly (driver and passenger). Refer to
SE-112, "Removal and Installation"
2.
Remove second seat assembly (LH and RH). Refer to
SE-125, "Removal and Installation"
.
3.
Remove floor grille (LH and RH). Refer to
VTL-12, "REAR FLOOR GRILLE : Removal and Installation"
4.
Remove front kicking plate inner and rear kicking plate inner (LH and RH). Refer to
PLATE INNER : Removal and Installation"
.
5.
Remove dash side finisher (LH and RH). Refer to
INT-18, "DASH SIDE FINISHER : Removal and Installa-
6.
Remove center pillar lower garnish (LH and RH). Refer to
INT-22, "CENTER PILLAR LOWER GARNISH :
.
7.
Remove instrument lower panel LH. Refer to
IP-14, "Removal and Installation"
8.
Remove center console assembly. Refer to
IP-25, "Removal and Installation"
.
9.
Remove adjusting nut and front cable mounting bolts and nuts, and then remove front cable. Refer to
176, "Removal and Installation"
JMJIA4008ZZ
1.
Front floor carpet
2.
Carpet hook
3.
Fixing clip
4.
Footrest
5.
Front floor spacer front
6.
Front floor spacer rear
7.
Floor hook
8.
Rear floor carpet
9.
Dual lock fastener
: Pawl
: Vehicle front
INT-26
< REMOVAL AND INSTALLATION >
FLOOR TRIM
10. Remove the following parts after removing the center console assembly.
• Remove ground bolt (G).
• Disconnect floor harness connectors (A) and (E).
• Disconnect yaw rate/side/decel G sensor harness connector (C). Refer to
• Disconnect diagnosis sensor unit harness connector (D). Refer to
• Remove floor harness clamps (B) and (F).
11. Remove A/T shift selector assembly mounting bolts. Refer to
TM-176, "Removal and Installation"
.
12. Remove floor duct 1 (LH and RH). Refer to
VTL-11, "FLOOR DUCT 1 : Removal and Installation"
.
13. Disconnect drain hose (1) and remove instrument stay mounting
nuts (A), and then remove instrument stay (2) (LH and RH).
14. Disengage front floor carpet from front floor carpet fixing clips
(A).
JMJIA4226ZZ
JMJIA4225ZZ
JMJIA1560ZZ
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
15. Peel off dual lock fastener between front floor carpet and rear floor carpet, and then remove front floor car-
pet.
INSTALLATION
Install in the reverse order of removal.
REAR FLOOR CARPET
REAR FLOOR CARPET : Removal and Installation
INFOID:0000000006220255
REMOVAL
1.
Remove third seat assembly. Refer to
SE-138, "Removal and Installation"
2.
Remove luggage floor rear board. Refer to
INT-34, "LUGGAGE FLOOR REAR BOARD : Removal and
.
3.
Remove luggage rear plate. Refer to
INT-35, "LUGGAGE REAR PLATE : Removal and Installation"
4.
Remove luggage floor bracket. Refer to
5.
Remove luggage side lower finisher. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal
6.
Disengage clip of each floor hook (1) using a remover tool (A),
and then remove each floor hook.
7.
Peel off dual lock fastener between front floor carpet and rear floor carpet, and then remove rear floor car-
pet.
INSTALLATION
Install in the reverse order of removal.
: Clip
JMJIA0092GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст