Infiniti QX56 (Z62). Manual — part 842
INT-16
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded View
INFOID:0000000006220243
Removal and Installation
INFOID:0000000006220244
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Rear door finisher
2.
Bumper rubber
3.
Door finisher cap
4.
Inside handle escutcheon
5.
Rear door grip cap
6.
Step lamp
7.
Power window switch finisher
8.
Power window switch
9.
Tweeter grille
10. Rear door garnish
11. Rear door tweeter
12. Rear door panel
13. Rear door inside handle
14. Rear door inside seal
: Clip
: Pawl
JMJIA4423ZZ
REAR DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REMOVAL
1.
Fully open door window.
2.
Remove door finisher cap (1) using a small flat-bladed screw-
driver (A) as shown by the arrow in the figure, and then remove
rear door finisher mounting bolt.
CAUTION:
Use a small flat-bladed screwdriver wrapped in tape (B).
3.
Insert a remover tool (A) between rear door grip cap (1) and rear
door grip to disengage rear door grip cap fixing pawls as shown
by the arrow in the figure, and then remove fixing screws.
4.
Remove step lamp, and then disconnect step lamp harness connector. Refer to
.
5.
Remove bumper rubber.
6.
Insert a remover tool (A) between rear door finisher and rear
door panel to disengage the clips as shown by the arrow in the
figure.
CAUTION:
Insert a remover tool into the part shown in the figure
(between the clips and the door panel).
7.
Disconnect mood lamp harness connector.
8.
Disconnect power window switch harness connector and clamp.
9.
Disconnect lock knob cable and inside handle cable from rear inside handle.
10. Remove rear door finisher from rear door panel.
11. Remove the following parts after removing rear door finisher.
• Mood lamp.
• Power window switch. Refer to
PWC-74, "Removal and Installation"
• Rear door inside handle. Refer to
DLK-244, "INSIDE HANDLE : Removal and Installation"
.
• Rear door tweeter. Refer to
AV-218, "Removal and Installation"
.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visualy check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing rear door finisher, check that clips and pawls are securely fitted in body panel holes,
and press them in.
: Pawl
JMJIA4013ZZ
: Pawl
JMJIA4016ZZ
: Clip
JMJIA4017ZZ
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000006220245
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000006220246
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVAL
1.
Remove front kicking plate inner. Refer to
INT-20, "KICKING PLATE INNER : Removal and Installation"
2.
Remove dash side finisher fixing clip (A).
1.
Front pillar garnish
2.
Assist grip
3.
Assist grip cap
4.
Dash side finisher
5.
Clip
6.
Front kicking plate inner
7.
Front body side welt
8.
Front kicking plate outer
9.
Center pillar lower garnish
10. Rear side bracket
11. Rear kicking plate inner
12. Rear body side welt
13. Rear kicking plate outer
14. Assist grip
15. Center pillar upper garnish
: Clip
: Pawl
: Metal clip
Refer to
for symbols in the figure.
JMJIA4307ZZ
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Disengage dash side finisher (1) fixing clips (A) using a remover
tool (B) as shown by the arrow in the figure, and then remove
dash side finisher.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing dash side finisher, check that clips are securely fitted in body panel holes, and press
clips in.
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000006220247
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVAL
1.
Release front pillar garnish portion of front body side welt.
2.
Disengage assist grip cap (1) fixing pawls using a flat-bladed
screwdriver (A) as shown in the figure, and then remove assist
grip mounting bolts and assist grip (2).
CAUTION:
Apply protective tape (B) to the assist grip to protect from
damage.
3.
Disengage front pillar garnish (1) fixing clip and metal clip using
a remover tool (A) as shown by the arrow in the figure, and then
remove front pillar garnish.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Visually check the clip, pawls and metal clip for deformation and damage during installation.
Replace with new ones if necessary.
• When installing front pillar garnish, check that clip and metal clip are securely fitted in body panel
holes, and press them in.
: Clip
JMJIA4020ZZ
: Pawl
JMJIA4018ZZ
: Clip
: Metal clip
JMJIA4019ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст