Infiniti EX35. Manual — part 711
OIL PAN (LOWER)
EM-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL PAN (LOWER)
Exploded View (2WD)
INFOID:0000000003139110
1.
Oil level gauge
2.
Oil level gauge guide
3.
O-ring
4.
O-ring
5.
Connector bolt
6.
Oil filter
7.
Plug
8.
Oil pressure switch
9.
Oil strainer
10. Oil temperature sensor
11.
Washer
12. Oil pan (upper)
13. Drain plug
14. Drain plug washer
15. Oil pan (lower)
16. Rear plate cover
A.
Refer to
B.
To oil pump
C.
Oil pan side
Refer to
for symbols in the figure.
JPBIA0530GB
EM-44
< ON-VEHICLE REPAIR >
OIL PAN (LOWER)
Exploded View (AWD)
INFOID:0000000003139111
Removal and Installation
INFOID:0000000003139112
REMOVAL
CAUTION:
Never drain engine oil when the engine is hot to avoid the danger of being scalded.
1.
Remove engine undercover with power tool.
2.
Drain engine oil. Refer to
.
3.
Remove oil pan (lower) as follows:
1.
Oil level gauge
2.
Oil level gauge guide
3.
O-ring
4.
O-ring
5.
Gasket
6.
Oil strainer
7.
Drain plug
8.
Drain plug washer
9.
Oil pan (lower)
10. O-ring (small)
11.
Axle pipe
12. O-ring (large)
13. Rear plate cover
14. Oil pan (upper)
A.
Refer to
B.
To oil pump
C.
Oil pan side
for symbols in the figure.
JPBIA1825GB
OIL PAN (LOWER)
EM-45
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order as shown in the figure to
remove.
b.
Insert the seal cutter [SST: KV10111100 (J37228)] (A) between
oil pan (upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surfaces.
• Never insert a screwdriver, this will damage the mating
surfaces.
c.
Slide the seal cutter [SST: KV10111100 (J37228)] by tapping on
the side of tool with a hammer. Remove oil pan (lower).
INSTALLATION
1.
Install oil pan (lower) as follows:
a.
Use scraper (A) to remove old liquid gasket from mating sur-
faces.
• Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Never scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the oil pan (lower) as shown in the
figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
: Engine front
JPBIA0021ZZ
JPBIA0276ZZ
JPBIA0025ZZ
: Engine front
a
:
φ
4.0 - 5.0 mm (0.157 - 0.197 in)
JPBIA1556ZZ
EM-46
< ON-VEHICLE REPAIR >
OIL PAN (LOWER)
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
(2WD models) and
(AWD models).
3.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
Inspection
INFOID:0000000003139113
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
: Engine front
JPBIA0021ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст