Infiniti EX35. Manual — part 975
FLOOR TRIM
INT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
6.
Remove front seat belt floor anchor bolt (LH/RH). Refer to
SB-7, "SEAT BELT BUCKLE : Exploded View"
.
7.
Remove center console assembly. Refer to
IP-22, "Removal and Installation"
.
8.
Remove instrument lower cover, instrument driver lower panel, instrument assist lower panel and instru-
ment side panel (LH/RH). Refer to
IP-12, "Removal and Installation"
9.
Remove G-sensor (1). Refer to
.
10. Remove diagnosis sensor unit (2). Refer to
11. Remove console rear bracket (3). Refer to
.
12. Remove floor harness mounting clamps (A).
13. Remove dash side finisher (LH/RH), front kicking plate inner (LH/RH) and body side welt (LH/RH). Refer
INT-20, "Removal and Installation"
.
14. Remove floor trim mounting clips and fixing nuts.
15. Remove floor trim from floor trim fixing clips (A) and remove floor
carpet.
INSTALLATION
Install in the reverse order of removal.
JMJIA0093GB
JMJIA1560ZZ
INT-26
< ON-VEHICLE REPAIR >
HEADLINING
HEADLINING
NORMAL ROOF
NORMAL ROOF : Exploded View
INFOID:0000000003591455
1.
Sun-visor assembly
2.
Sun-visor holder
3.
Sun-visor cover
4.
Assist grip cap
5.
Assist grip
6.
Headlining assembly
7.
Front camera finisher
8.
Over head console
9.
Map lamp assembly
10. Map lamp lens
11. Bracket map lamp
12. Roof plate assembly
13. Dual lock fastener
14. Antenna feeder harness
15. Front roof finisher
16. Personal lamp assembly
: Clip
: Pawl
: Metal clip
JMJIA1681ZZ
HEADLINING
INT-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
NORMAL ROOF : Removal and Installation
INFOID:0000000003591456
REMOVAL
1.
Remove rear seat cushion and seat back. Refer to
SE-99, "Removal and Installation"
.
2.
Remove front seat belt anchor bolt (LH/RH). Refer to
SB-7, "SEAT BELT BUCKLE : Exploded View"
3.
Remove rear seat belt anchor bolt (LH/RH). Refer to
SB-12, "SEAT BELT BUCKLE : Exploded View"
4.
Remove luggage side lower finisher (LH/RH), luggage side upper finisher (LH/RH). Refer to
5.
Remove front pillar garnish (LH/RH), front kicking plate (LH/RH), center pillar lower garnish (LH/RH), cen-
ter pillar upper garnish (LH/RH), front body side welt (LH/RH), rear body side welt (LH/RH), rear kicking
plate (LH/RH). Refer to
INT-20, "Removal and Installation"
6.
Disconnect roof harness connectors (A) and clips (B), then
remove the roof harness (1).
7.
Remove front roof finisher mounting pawls with remover tool (A),
then remove front roof finisher (1).
8.
Remove the front camera finisher mounting pawls with a
remover tool (A), then remove the front camera finisher.
9.
Remove sun-visor (LH/RH).
• Remove sun-visor cap.
• Remove mounting screws.
• Disconnect vanity mirror lamp harness connector (With vanity mirror lamp)
10. Disconnect inside mirror harness connector.
: Clip
JMJIA1565ZZ
: Pawl
: Metal clip
JMJIA1564ZZ
: Pawl
JMJIA1567ZZ
INT-28
< ON-VEHICLE REPAIR >
HEADLINING
11. Insert a small flatted-blade screwdriver (A) into the hole of the
sun-visor holder (1), press while rotating approximately 90
degrees to remove.
12. With a small flatted-blade screwdriver (A), press the upper side
mounting plastic clip (1) and pull up to remove the mounting
plastic clip (1) from assist grip (2).
•
13. Once the mounting plastic clip (1) is removed, pull out the assist
grip (2) to remove.
14. Recline front seat back to facilitate the headlining removal.
15. Pull map lamp assembly toward and disengage metal clips (B)
and dual-lock fastener (A).
CAUTION:
Map lamp assembly is crimped from the back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
16. Using remover tool, remove headlining hidden clip at the back side of headlining.
JMJIA1706ZZ
JMJIA1379ZZ
JMJIA1380ZZ
: Metal clip
JMJIA1008ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст