Infiniti EX35. Manual — part 1463
TM-240
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
44. Install band servo anchor end pin and lock nut in transmission
case.
45. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
46. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
47. Install needle bearing to front sun gear.
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
48. Adjust brake band tilting using a clip so that brake band contacts
front sun gear drum evenly.
SCIA6512E
SCIA5498E
SCIA5014E
SCIA2808E
SCIA5033E
TRANSMISSION ASSEMBLY
TM-241
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
49. Adjust brake band.
a.
Loosen lock nut.
b.
Tighten band servo anchor end pin to specified torque.
c.
Back of band servo anchor end pin three turns.
d.
Holding band servo anchor end pin, tighten lock nut to the spec-
ified torque.
50. Adjustment of total end play.
• Measure clearance between front sun gear and bearing race
for oil pump cover.
• Select proper thickness of bearing race so that end play is
within specifications.
a.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
i.
Measure dimension “K”.
: 5.0 N·m (0.51 kg-m, 44 in-lb)
SCIA5498E
SCIA2810E
SCIA7073E
SCIA7074E
TM-242
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
ii.
Measure dimension “L”.
iii.
Calculate dimension “J”.
b.
Measure dimensions “M
1
” and “M
2
” and then calculate dimen-
sion “M”.
i.
Place bearing race and needle bearing on oil pump assembly.
ii.
Measure dimension “M
1
”.
iii.
Measure dimension “M
2
”.
“J”
: Distance between oil pump fitting surface of
transmission case and needle bearing mating
surface of front sun gear.
J = K – L
SCIA5352E
SCIA3125E
SCIA3124E
SCIA3126E
SCIA3127E
TRANSMISSION ASSEMBLY
TM-243
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
iv.
Calculate dimension “M”.
c.
Adjust total end play “T
1
”.
• Select proper thickness of bearing race so that total end play
is within specifications.
51. Install O-ring to oil pump assembly.
52. Install bearing race to oil pump assembly.
53. Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump bearing.
“M”
: Distance between transmission case fitting
surface of oil pump and needle bearing on oil
pump.
M = M
1
– M
2
SCIA3125E
T
1
= J – M
Total end play “T
1
”
: Refer to
.
Bearing races
: Refer to
.
SCIA2810E
SCIA5172E
SCIA6529E
SCIA2811E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст