Infiniti EX35. Manual — part 861
FRONT COIL SPRING AND STRUT
FSU-29
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
1.
Install strut attachment (A) [SST: ST35652000 (
–
)] to strut
and secure it in a vise.
CAUTION:
When installing the strut attachment to strut, wrap a shop
cloth around strut to protect it from damage.
2.
Using a spring compressor (A) (commercial service tool), com-
press coil spring between rubber seat and strut until coil spring
with a spring compressor is free.
CAUTION:
Be sure a spring compressor is securely attached coil
spring. Compress coil spring
3.
Make sure coil spring with a spring compressor between rubber
seat and strut is free. And then remove piston rod lock nut while
securing the piston rod tip so that piston rod does not turn.
4.
Remove mounting seal, strut mounting bracket, rubber seat,
bound bumper from strut.
5.
After remove coil spring with a spring compressor, and then
gradually release a spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6.
Remove the strut attachment from strut.
ASSEMBLY
1.
Install strut attachment (A) [SST: ST35652000 (
−
)] to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut, wrap a shop cloth around strut to protect it from
damage.
2.
Compress coil spring using a spring compressor (commercial service tool), and install it onto strut.
CAUTION:
• Install with the large-diameter side (A) facing up and the
small-diameter side (B) facing down.
• Be sure a spring compress or is securely attached to coil
spring. Compress coil spring.
3.
Install the strut mounting bracket and rubber seat.
CAUTION:
Align the paint mark (A) to the stud bolt (1) position when
assembling.
4.
Apply soapy water to bound bumper.
CAUTION:
Never use machine oil.
JPEIA0006ZZ
JPEIA0007ZZ
PEIA0108E
JPEIA0009ZZ
FSU-30
< ON-VEHICLE REPAIR >
[AWD]
FRONT COIL SPRING AND STRUT
5.
Insert bound bumper into strut mounting bracket, and then install it to strut together with rubber seat.
• Install the strut mounting bracket as shown in the figure.
• Check that the lower end of the coil spring (C) is positioned at the spring lower seat of the strut.
6.
Secure piston rod tip so that piston rod does not turn, then tighten piston rod lock nut with specified
torque.
7.
Gradually release a spring compressor, and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
8.
Remove the strut attachment from strut.
9.
Install the mounting seal to strut mounting bracket.
Inspection
INFOID:0000000003129937
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-107, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
INSPECTION AFTER DISASSEMBLY
Strut
Check the following items, and replace the part if necessary.
• Strut for deformation, cracks or damage.
• Piston rod for damage, uneven wear or distortion.
1. Strut mounting bracket
A. Right side
B. Left side
: Vehicle front
Angle (a)
: 35.4
°
JPEIA0080ZZ
FRONT COIL SPRING AND STRUT
FSU-31
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Oil leakage.
Strut Mounting Bracket and Rubber Parts Inspection
Check strut mounting bracket for cracks and rubber parts for wear. Replace it if necessary
Coil Spring
Check coil spring for cracks, wear or damage. Replace it if necessary.
FSU-32
< ON-VEHICLE REPAIR >
[AWD]
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000003129938
Removal and Installation
INFOID:0000000003129939
REMOVAL
1.
Remove tires with power tool.
2.
Remove under cover with power tool.
3.
Remove strut. Refer to
4.
Remove front crossbar. Refer to
.
5.
Remove steering outer socket from steering knuckle. Refer to
6.
Remove transverse link from steering knuckle.
7.
Set suitable jack under transverse link.
8.
Remove transverse link and insulator.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never tap on the ball joint cap of the stabilizer connecting rod with a hammer or a similar item when inserting
the stabilizer connecting rod into the transverse link.
• Perform final tightening of bolts and nuts at the front suspension member installation and strut lower side
(rubber bushing), under unladen conditions with tires on level ground.
Inspection
INFOID:0000000003129940
INSPECTION AFTER REMOVAL
Appearance
Check the following items, and replace the part if necessary.
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
1.
Stopper rubber
2.
Upper link
3.
Insulator
4.
Transverse link
5.
Front suspension member
Refer to
for symbols in the figure.
JPEIA0087GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст