Infiniti EX35. Manual — part 862
TRANSVERSE LINK
FSU-33
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
• Hook a spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
- If swing torque exceeds standard range, replace transverse link
assembly.
Rotating Torque Inspection
• Attach mounting nut to ball stud. Make sure that rotating torque is
within specifications with a preload gauge (A) [SST: 3127S000 (J-
25765-A)].
- If rotating torque exceeds standard range, replace transverse link
assembly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If axial end play exceeds standard range, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-107, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Standard
Swing toque
JPEIA0005ZZ
Standard
Rotating toque
: Refer to
.
PDIA1258E
Standard
Axial end play
:Refer to
.
FSU-34
< ON-VEHICLE REPAIR >
[AWD]
UPPER LINK
UPPER LINK
Exploded View
INFOID:0000000003129941
Removal and Installation
INFOID:0000000003129942
REMOVAL
1.
Remove tires from with power tool.
2.
Remove strut. Refer to
3.
Remove upper link from steering knuckle with power tool.
4.
Remove upper link and stopper rubber with power tool.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000003129943
INSPECTION AFTER REMOVAL
Appearance
Check the following items, and replace the part if necessary.
• Upper link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
1.
Stopper rubber
2.
Upper link
3.
Insulator
4.
Transverse link
5.
Front suspension member
Refer to
for symbols in the figure.
JPEIA0087GB
UPPER LINK
FSU-35
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Hook a spring balance (A) at cutout on ball stud. Confirm spring
balance measurement value is within specifications when ball stud
begins moving.
- If swing torque exceeds standard range, replace upper link assem-
bly.
Rotating Torque Inspection
• Attach mounting nut to ball stud. Make sure that rotating torque is
within specifications with a preload gauge (A) [SST: ST3127S000
(J-25765-A)].
- If rotating torque exceeds torque range, replace upper link assem-
bly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If axial end play exceeds standard range, replace upper link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-107, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Standard
Swing torque
: Refer to
JPEIA0005ZZ
Standard
Rotarian torque
: Refer to
PDIA1258E
Standard
Axial end play
: Refer to
FSU-36
< ON-VEHICLE REPAIR >
[AWD]
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000003129944
Removal and Installation
INFOID:0000000003129945
REMOVAL
1.
Remove tires with power tool.
2.
Remove under cover with power tool.
3.
Remove stabilizer connecting rod with power tool.
CAUTION:
Apply a matching mark to identify the installation position.
4.
Remove stabilizer clamp and stabilizer bushing.
5.
Remove stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the matching mark when installing.
• Tighten the mounting nut to the specified torque while holding a hexagonal part of stabilizer connecting rod
side.
Inspection
INFOID:0000000003129946
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
1.
Stabilizer bar
2.
Stabilizer bushing
3.
Stabilizer clamp
4.
Stabilizer connecting rod
Refer to
for symbols in the figure.
JPEIA0088GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст