Infiniti EX35. Manual — part 98
A V
DIAGNOSIS AND REPAIR WORKFLOW
AV-173
< BASIC INSPECTION >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
1.
Connect CONSULT-III and perform a self-diagnosis for “MULTI AV”. Refer to
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2.
Check if any DTC is displayed in the self-diagnosis results.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1.
Check the DTC indicated in the self-diagnosis results.
2.
Perform the relevant diagnosis referring to the DTC Index. Refer to
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1.
Repair or replace the identified malfunctioning parts.
2.
Perform a self-diagnosis for “MULTI AV” with CONSULT-III.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3.
Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> INSPECTION END
AV-174
< BASIC INSPECTION >
[BOSE AUDIO WITHOUT NAVIGATION]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003528840
WITH REAR VIEW MONITOR
Always correct the center position of the predicted course line after disconnecting the battery negative termi-
nal.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003528841
1.
CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to
AV-174, "PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003528842
When camera control unit is replaced, the center position of predicted course line shall be corrected.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003528843
1.
CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to
AV-174, "PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
.
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000003528844
Adjust the center position of the predicted course line of the rear view monitor if it is shifted.
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special Repair
Requirement
INFOID:0000000003528845
1.
STEERING OPERATION
Steer the steering wheel to the leftmost and rightmost ends.
>> GO TO 2
2.
DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
AV
MULTI AV SYSTEM
AV-175
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FUNCTION DIAGNOSIS
MULTI AV SYSTEM
System Diagram
INFOID:0000000003508650
WITHOUT REAR VIEW MONITOR
NOTE:
• The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
• A radio antenna base integrated with radio antenna and satellite
radio antenna is adopted.
JSNIA0692GB
JSNIA1062GB
AV-176
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM
WITH REAR VIEW MONITOR
NOTE:
• The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
• A radio antenna base integrated with radio antenna and satellite
radio antenna is adopted.
System Description
INFOID:0000000003508651
Multi AV system means that the following systems are integrated.
JSNIA0693GB
JSNIA1062GB
System name
System explanation
AUDIO SYSTEM
VEHICLE INFORMATION SYSTEM
• Indicates the status of audio, climate control system, fuel econ-
omy and maintenance.
• AV control unit displays the fuel consumption status while re-
ceiving data signal through CAN communication from ECM, uni-
fied meter and A/C amp.
• AV control unit is connected to BCM via CAN communication
transmitting/receiving for the vehicle settings function.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст