Infiniti EX35. Manual — part 1444
TM-164
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
13. Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Be careful not to damage connector.
14. Disengage terminal clips (
).
15. Disconnect revolution sensor connector (A).
CAUTION:
Be careful not to damage connector.
16. Disengage terminal clip (
).
17. Remove bolts (A), (B) and (C) from control valve with TCM.
18. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve (1) notch
and manual plate (2) height. Remove it vertically.
19. Remove A/T fluid temperature sensor 2 (1) with bracket (2) from
control valve with TCM.
SCIA8124E
JPDIA0011ZZ
: Vehicle front
SCIA8074E
JPDIA0012ZZ
: Bolt
JPDIA0013ZZ
CONTROL VALVE WITH TCM
TM-165
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
20. Remove bracket (1) from A/T fluid temperature sensor 2 (2).
21. Remove O-ring (1) from A/T assembly harness connector (A).
22. Disconnect TCM connectors (A) and (B).
CAUTION:
Be careful not to damage connectors.
23. Remove A/T assembly harness connector (A) from control valve
with TCM using flat-blade screwdriver (B).
24. Disconnect TCM connector (A) and park/neutral position switch
connector (B).
CAUTION:
Be careful not to damage connectors.
JPDIA0014ZZ
JPDIA0015ZZ
JPDIA0016ZZ
JPDIA0017ZZ
JPDIA0018ZZ
TM-166
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Be careful not to damage connector when installing any connector.
• Do not reuse drain plug gasket.
• Do not reuse O-ring.
• Apply ATF to O-ring.
• Adjust bolt hole of bracket to bolt hole of control valve with TCM when installing A/T fluid tempera-
ture sensor 2 (with bracket).
• Refer to the followings when installing control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole (B).
• Hang down revolution sensor harness toward outside so as
not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve (1) cutout is engaged with
manual plate (2) projection.
- Install bolts (A), (B) and (C) in control valve with TCM. Tighten bolt
1, 2 and 3 temporarily to prevent dislocation. After that tighten
them in order (1
→
2
→
3), and then tighten other bolts. Tighten
control valve with TCM bolts to the specified torque.
A
: Brake band
JPDIA0020ZZ
JPDIA0012ZZ
: Vehicle front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length
mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (km-g, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
CONTROL VALVE WITH TCM
TM-167
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Refer to the followings when installing oil pan (2) (with oil pan gas-
ket) and clips (1) to transmission case.
CAUTION:
• Do not reuse oil pan gasket and oil pan mounting bolts.
• Install oil pan gasket in the direction to align hole position.
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
- Tighten oil pan mounting bolts to the specified torque in numerical
order shown in the figure after temporarily tightening them. Tighten
oil pan mounting bolts to the specified torque.
Inspection
INFOID:0000000003130613
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
.
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage and A/T fluid level after completing installation. Refer to
.
: Vehicle front
: Oil pan mounting bolt
: Vehicle front
SCIA8117E
JPDIA0021ZZ
SCIA5199E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст