Infiniti EX35. Manual — part 1443
TM-160
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL DEVICE
b.
Remove insert finisher (1) from console finisher assembly.
c.
Remove the selector lever position indicator (1).
15. Remove adapter from control device assembly.
16. Remove dust cover and dust cover plate from control device
assembly.
17. Remove dust cover plate from dust cover.
18. Remove shift lock unit from control device assembly.
19. Remove bracket from vehicle floor panel.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control rod to control device assembly, refer to “ADJUSTMENT”. Refer to
AWD : Inspection and Adjustment
INFOID:0000000003130605
INSPECTION AFTER INSTALLATION
Check the A/T positions. Refer to
TM-153, "AWD : Inspection and Adjustment"
.
A
: Screw (small)
B
: Screw (large)
JPDIA0636ZZ
: Screw
JPDIA0637ZZ
CONTROL ROD
TM-161
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL ROD
Exploded View
INFOID:0000000003130606
Removal and Installation
INFOID:0000000003130607
REMOVAL
1.
Disconnect control device and control rod. Refer to
(2WD models),
(AWD models).
2.
Remove manual lever from A/T assembly.
3.
Remove control rod from manual lever.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing control rod to control device assembly, refer to “ADJUSTMENT”. Refer to
TM-153, "AWD : Inspection and Adjustment"
(AWD models).
Inspection and Adjustment
INFOID:0000000003130608
INSPECTION AFTER INSTALLATION
Check A/T positions. Refer to
TM-153, "2WD : Inspection and Adjustment"
(2WD models),
(AWD models).
1.
Control rod
2.
Plain washer
3.
Manual shaft
4.
A/T assembly
5.
Manual lever
6.
Washer
7.
Snap pin
8.
Conical washer
9.
Insulator
10.
Collar
for symbols in the figure.
JPDIA0638GB
TM-162
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
CONTROL VALVE WITH TCM
Exploded View
INFOID:0000000003130611
Removal and Installation
INFOID:0000000003130612
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust mounting bracket. Refer to
1.
A/T
2.
Snap ring
3.
Sub-harness
4.
Bracket
5.
Control valve with TCM
6.
Bracket
7.
A/T fluid temperature sensor 2
8.
Oil pan gasket
9.
Clip
10. Oil pan mounting bolt
11.
Oil pan
12. Magnet
13. Drain plug
14. Drain plug gasket
15. Terminal cord assembly
16. O-ring
A.
For tightening torque, refer to “Installation”.
Refer to
for symbols in the figure.
JPDIA0646GB
CONTROL VALVE WITH TCM
TM-163
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Disconnect heated oxygen sensor 2 harness connectors (A).
5.
Remove heated oxygen sensor 2 harness (B) from clips (1).
6.
Remove bracket (2) from transmission assembly.
7.
Disconnect A/T assembly harness connector.
8.
Remove snap ring (1) from A/T assembly harness connector
(A).
9.
Push A/T assembly harness connector (A).
CAUTION:
Be careful not to damage connector.
10. Remove clips (1).
11. Remove oil pan (2) and oil pan gasket.
12. Remove magnets (1) from oil pan.
: Vehicle front
: Bolt
SCIA8269E
JPDIA0007ZZ
JPDIA0008ZZ
3
: Drain plug
: Vehicle front
: Oil pan mounting bolt
SCIA8117E
JPDIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст