Infiniti EX35. Manual — part 1244
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
17. Remove pin stay.
18. Remove rear suspension member mounting nuts.
19. Slowly lower jack, then remove rear suspension member, suspension arm, front lower link, wheel hub and
housing from vehicle as a unit.
20. Remove mounting bolts and nuts, then remove suspension arm, front lower link, wheel hub and housing
from rear suspension member. Refer to
,
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Check wheel sensor harness for proper connection. Refer to
.
• Never reuse cotter pin.
Inspection
INFOID:0000000003130399
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation (stroke).
PB-3, "Inspection and Adjustment"
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000003130403
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000003130404
Wheel Height
INFOID:0000000003130405
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
05
′
(–1.08
°
)
Nominal
–0
°
35
′
(–0.58
°
)
Maximum
–0
°
05
′
(–0.09
°
)
Total toe-in
Distance
Minimum
0 mm (0 in)
Nominal
In 2.9 mm (0.114 in)
Maximum
In 5.8 mm (0.228 in)
Angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
In 0
°
07
′
(0.12
°
)
Maximum
In 0
°
14
′
(0.23
°
)
Item
Standard
Swing torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Measurement on spring balance (cotter pinhole position)
8.1 – 54.8 N (0.83 – 5.59 kg, 1.83 – 12.31 lb)
Rotating torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Axial end play
0 mm (0 in)
Tire
225/60R17
225/55R18
Rear (Hr)
757 mm (29.80 in)
762 mm (30.00 in)
SFA818A
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . ..
FRONT SEAT BELT . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . . ..
SEAT BELT RETRACTOR : Inspection . . . . ....
SEAT BELT RETRACTOR : Exploded View . . .....
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . ..
SEAT BELT BUCKLE . . . . . . . . . . . .....
SEAT BELT BUCKLE : Inspection . . . . . . ....
SEAT BELT BUCKLE : Exploded View . . . . ....
SEAT BELT BUCKLE : Removal and Installation . .
REAR SEAT BELT . . . . . . . . . . . .
SEAT BELT RETRACTOR . . . . . . . . . . .
SEAT BELT RETRACTOR : Inspection . . . . ...
SEAT BELT RETRACTOR : Exploded View . . ...
SEAT BELT RETRACTOR : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
SEAT BELT BUCKLE . . . . . . . . . . . .
SEAT BELT BUCKLE : Inspection . . . . . . ..
SEAT BELT BUCKLE : Exploded View . . . . ...
SEAT BELT BUCKLE : Removal and Installation .
LATCH SYSTEM FOR CHILDREN . . . . ...
Exploded View . . . . . . . . . . . . . . .
SB-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003514797
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Seat Belt Service
INFOID:0000000003134253
CAUTION:
• Before removing the front seat belt pre-tensioner assembly, turn the ignition switch off, disconnect
battery negative terminal and wait at least 3 minutes.
• Do not use electrical test equipment for front seat belt pre-tensioner connector.
• After replacing or reinstalling front seat belt pre-tensioner assembly, or reconnecting front seat belt
pre-tensioner connector, check the system function. Refer to
SRC-14, "Diagnosis Description"
.
• Do not use disassembled buckle or seat belt assembly.
• Replace anchor bolts if they are deformed or worn out.
• Never oil tongue and buckle.
• If any component of seat belt assembly is questionable, do not repair. Replace the entire seat belt
assembly.
• If webbing is cut, frayed or damaged, replace seat belt assembly.
• When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.
AFTER A COLLISION
WARNING:
Inspect all seat belt assemblies including retractors and attached hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners
should be replaced even if the seat belts are not in use during a frontal collision in which the air bags
are deployed.
Replace any seat belt assembly (including anchor bolts) if:
• The seat belt was in use at the time of a collision (except for minor collisions and the belts, retractors and
buckles show no damage and continue to operate properly).
• The seat belt was damaged in an accident (i.e. torn webbing, bent retractor or guide).
• The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The front seat belt pre-tensioner should be replaced even if the seat belts are not in use during the collision
in which the air bags are deployed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст