Infiniti EX35. Manual — part 863
FRONT SUSPENSION MEMBER
FSU-37
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000003129947
Removal and Installation
INFOID:0000000003129948
REMOVAL
1.
Remove tire with power tool.
2.
Remove under cover with power tool.
3.
Remove front cross bar with power tool.
4.
Separate steering gear assembly and lower joint. Refer to
5.
Remove steering outer socket from steering knuckle. Refer to
.
6.
Remove wheel sensor and sensor harness from steering knuckle. Refer to
.
7.
Remove strut from transverse link. Refer to
.
8.
Remove stabilizer connecting rod and stabilizer bar. Refer to
.
9.
Install engine slinger, and then hoist engine.
10. Remove transverse link from front suspension member with power tool. Refer to
.
11. Remove steering hydraulic piping bracket and steering gear from front suspension member. Refer to
12. Set suitable jack front suspension member.
13. Remove mounting nuts between engine mounting insulator and from suspension member. Refer to
14. Remove mounting bolts and nuts of front suspension member with power tool.
15. Gradually lower jack to remove front suspension assembly from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nut at the vehicle installation position (rubber bushing), under unladen
condition with tires on level ground.
1.
Front suspension member
2.
Front cross bar
Refer to
JPEIA0089GB
FSU-38
< ON-VEHICLE REPAIR >
[AWD]
FRONT SUSPENSION MEMBER
Inspection
INFOID:0000000003129949
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-107, "FRONT WHEEL SENSOR :
.
2.
Check wheel alignment. Refer to
3.
Adjust the neutral position of the steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-39
< SERVICE DATA AND SPECIFICATIONS (SDS)
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000003129953
Measure value under unladen* conditions.
*Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000003129954
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
05
′
(–1.08
°
)
Nominal
–0
°
20
′
(–0.33
°
)
Maximum
0
°
25
′
(0.42
°
)
Left and right difference
0
°
33
′
(0.55
°
) or less
Caster
Degree minute (Decimal degree)
Minimum
3
°
25
′
(3.42
°
)
Nominal
4
°
10
′
(4.17
°
)
Maximum
4
°
55
′
(4.91
°
)
Left and right difference
0
°
39
′
(0.65
°
) or less
Kingpin inclination
Degree minute (Decimal degree)
Minimum
6
°
35
′
(6.58
°
)
Nominal
7
°
20
′
(7.33
°
)
Maximum
8
°
05
′
(8.08
°
)
Total toe-in
Distance
Minimum
0 mm (0 in)
Nominal
In 1 mm (0.04 in)
Maximum
In 2 mm (0.08 in)
Angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
In 0
°
02
′
24
″
(0.04
°
)
Maximum
In 0
°
04
′
48
″
(0.08
°
)
Item
Standard
Swing torque
Transverse link
0.5 – 3.6 N·m (0.06 – 0.36 kg-m, 5 – 31 in-lb)
Upper link
0 – 2.0 N·m (0 – 0.20 kg-m, 0 – 17 in-lb)
Measurement on spring balance
Transverse link
7.8 – 56.3 N (0.8 – 5.7 kg, 1.8 – 12.6 lb)
Upper link
0 – 61.5 N (0 – 6.2 kg, 0 – 13.8 lb)
Rotating torque
Transverse link
0.5 – 3.9 N·m (0.06 – 0.39 kg-m, 5 – 34 in-lb)
Upper link
0 – 2.0 N·m (0 – 0.2 kg-m, 0 – 17 in-lb)
Axial end play
0 mm (0 in)
FSU-40
< SERVICE DATA AND SPECIFICATIONS (SDS)
[AWD]
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Height
INFOID:0000000003129955
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Tire size
225/60R17
225/55R18
Front (Hf)
742 mm (29.21 in)
747 mm (29.41 in)
SFA818A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст