Infiniti G35 (V35) Sedan. Manual — part 405
DLN-54
< ON-VEHICLE REPAIR >
[TRANSFER: ETX13B]
REAR OIL SEAL
1.
Apply ATF to rear oil seal, install it with drifts.
CAUTION:
• Never reuse rear oil seal.
• When installing, never incline rear oil seal.
2.
Align the matching mark of mainshaft with the mark of compan-
ion flange, then install the companion flange.
3.
Using a flange wrench, install the self-lock nut of companion
flange and tighten to the specified torque.
CAUTION:
Never reuse self-lock nut.
4.
Install the rear propeller shaft. Refer to
.
5.
Check fluid level. Refer to
A: Drift [ST30720000 (J-25405)]
B: Drift [KV40104830 (
—
)]
Dimension “L”
: 6.7 – 7.3 mm (0.264 – 0.287 in)
JSDIA0167ZZ
SDIA2378E
PDIA0245E
TRANSFER ASSEMBLY
DLN-55
< REMOVAL AND INSTALLATION >
[TRANSFER: ETX13B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000000957289
Removal and Installation
INFOID:0000000000957290
REMOVAL
1.
Remove exhaust front tube with power tool. Refer to
2.
Remove front propeller shaft. Refer to
.
3.
Remove rear propeller shaft. Refer to
4.
Disconnect AWD solenoid harness connector and separate harness from transfer assembly.
5.
Remove transfer air breather hose.
6.
Remove control rod. Refer to
7.
Support transfer assembly and transmission assembly with a jack.
8.
Remove rear engine mounting member and engine mounting insulator with power tool. Refer to
9.
Lower jack to the position where the top transfer mounting bolts
can be removed.
10. Remove transfer mounting bolts with power tool and separate
transfer from transmission.
CAUTION:
Secure transfer assembly and transmission assembly to a
jack.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Transfer assembly
: Vehicle front
Refer to
JSDIA0052GB
PDIA0560J
DLN-56
< REMOVAL AND INSTALLATION >
[TRANSFER: ETX13B]
TRANSFER ASSEMBLY
• When installing the transfer to the transmission, install the mount-
ing bolts following the standard below, tighten bolts to the specified
torque.
• When installing transfer air breather hose, make sure there are no pinched or restricted areas on the transfer
air breather hose caused by bending or winding.
- Set transfer air breather hose with paint mark facing upward.
- Be sure to insert transfer air breather hose (1) into breather tube
(2) until hose end reaches the tube's base.
- Do not deviate from the range (L) of the transfer air breather when
installing the transfer air breather hose (1) to the harness bracket
(2) of the transfer.
- Install transfer air breather hose (1) with bracket between the
adapter case (2) and the transmission case (3).
Bolt No.
1
2
3
4
Quantity
4
3
2
1
Bolt length “
” mm (in)
75 (2.95)
45 (1.77)
40 (1.57)
30 (1.18)
SDIA2284E
JSDIA0053ZZ
JSDIA0054ZZ
JSDIA0055ZZ
TRANSFER ASSEMBLY
DLN-57
< REMOVAL AND INSTALLATION >
[TRANSFER: ETX13B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
- Check that transfer breather hose is on the (
) side when install-
ing the transfer air breather hose (1) to A/T fluid charging pipe (2).
- Be sure to insert air breather hose to transfer tube until hose end
reaches the tube's base and another hose end reaches the tube
bend R portion of A/T fluid charging pipe.
• After the installation, check the fluid level, fluid leakage and the A/T
positions. Refer to
.
JSDIA0056ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст