Infiniti G35 (V35) Sedan. Manual — part 11
ADP-38
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Parts Location
INFOID:0000000000960609
Order
Input
Output
Control unit condition
1
Door switch/Ignition
switch
—
Driver seat control unit receives the signals of [ignition switch signal]
and [driver side door switch] from BCM via CAN communication.
2
—
Motors
(Sliding, tilt, tele-
scopic)
Driver side control unit operates the sliding motor when the operating
conditions are satisfied and requests the operations of tilt motor and
telescopic motor to automatic drive positioner control unit via UART
communication. The automatic drive positioner operates each motor.
Sensors
(Sliding, tilt, telescop-
ic)
—
Each sensor monitors the operating positions of seat and steering,
and then stops the operation of each motor when each part reaches
the recorded address.
JMJIA0161GB
1.
BCM M118, M119, M122, M123
2.
Automatic drive positioner control unit
M51, M52
3.
Driver seat control unit B451, B452
4.
Unified meter and A/C amp. M67
5.
AV control unit
With NAVI M87, M88
Without NAVI M83, M85
6.
AT assembly connector F51
7.
Tilt & telescopic switch M31
8.
Key slot M22
9.
Tilt sensor M48
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-39
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
10. Telescopic sensor M48
11.
Seat memory switch D5
12. Door mirror remote control switch
D17
A.
Dash side lower (Passenger side)
B.
View with instrument driver lower
panel removed
C.
Backside of seat cushion (driver side)
D.
Behind cluster lid C
E.
AT assembly
(TCM is built in AT assembly)
F.
View with instrument driver lower
panel removed
G
View with steering column cover low-
er and upper removed
13. Front door switch (driver side) B16
14. AT device (detention switch) M137
15. Parking brake switch B14
16. Door mirror (driver side) D3
17. Telescopic motor M49
18. Tilt motor M49
H.
View with center console assembly
removed
I.
View with center console assembly
removed
J.
View with instrument driver lower
panel removed
19. Side support (seat cushion)
(Side support unit B420)
20. Reclining motor B454
21. Side support (seatback)
(Side support unit B420)
22. Side support unit B420
23. Reclining switch
(Power seat switch B459)
24. Sliding, lifting switch
(Power seat switch B459)
25. Side support switch (seat back side)
B419
26. Side support switch (cushion side)
B419
27. Sliding sensor B453
JMJIA0162GB
JMJIA0164GB
ADP-40
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Description
INFOID:0000000000960610
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
INTELLIGENT KEY INTERLOCK FUNCTION
28. Lifting motor (front) B455
29. Sliding motor B461
30. Lifting motor (rear) B456
K.
View with seat cushion pad and seat-
back pad removed
L.
Backside of the seat cushion
Item
Function
Driver seat control unit
According to the ignition signal and door switch signal (driver side) from BCM,
• Operates the seat sliding motor for a constant amount.
• Requests the operations of tilt motor and telescopic motor to automatic drive po-
sitioner control unit.
Automatic drive positioner control unit
Operates the tilt motor and telescopic motor with the instructions from the driver seat
control.
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
• Driver door: OPEN/CLOSE
• Ignition switch psition: ACC/ON
Item
Function
Front door switch (driver side)
Detect front door (driver side) open/close status.
Item
Function
Tilt & telescopic sensor
Detect the up/down and left/right position of steering column.
Sliding sensor
Detect the front/rear position of seat.
Item
Function
Tilt & telescopic motor
Move the steering column upward/downward and frontward/rearward.
Sliding motor
Slide the seat frontward/rearward.
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-41
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION : System Diagram
INFOID:0000000000960611
INTELLIGENT KEY INTERLOCK FUNCTION : System Description
INFOID:0000000000960612
OUTLINE
When unlocking doors by using Intelligent Key or driver side door request switch, the system performs mem-
ory operation, exiting operation then entry operation.
OPERATION PROCEDURE
1.
Unlock doors by using Intelligent Key or driver side door request switch.
2.
The system performs memory operation, and then performs exit assist operation.
NOTE:
If the seat position is in memorized position before unlocking doors, memory operation does not perform.
NOTE:
Further information for Intelligent Key interlock function. Refer to
ADP-10, "MEMORY STORING : Descrip-
.
OPERATION CONDITION
Satisfy all of the following items. The Intelligent Key interlock function is not performed if these items are not
satisfied.
JMJIA0117GB
Item
Request status
Ignition position
OFF
System setting [Entry/exit function (seat/steering)]
ON
Key switch
OFF (Key is removed.)
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror control switch
• Set switch
• Memory switch
OFF
(Not operated)
AT selector lever (only for AT model)
P position
Parking break (only for MT models)
Applied
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст