Infiniti G35 (V35) Sedan. Manual — part 10
ADP-34
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
EXIT ASSIST FUNCTION : Component Parts Location
INFOID:0000000000960605
Order
Input
Output
Control unit condition
1
Door switch
(Driver side)
—
Driver seat control unit receives door switch signal (driver side/
open) from BCM via CAN communication.
2
—
Motors
(Seat sliding, tilt,
telescopic )
Driver seat control unit operates the seat sliding motor, which recog-
nizes that the driver side door is opened with ignition switch OFF.
Driver seat control unit then requests the operations of tilt motor and
telescopic motor to auto drive positioner control unit via UART com-
munication. The automatic drive positioner control unit operates
each motor for a constant amount.
JMJIA0161GB
1.
BCM M118, M119, M122, M123
2.
Automatic drive positioner control unit
M51, M52
3.
Driver seat control unit B451, B452
4.
Unified meter and A/C amp. M67
5.
AV control unit
With NAVI M87, M88
Without NAVI M83, M85
6.
AT assembly connector F51
7.
Tilt & telescopic switch M31
8.
Key slot M22
9.
Tilt sensor M48
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-35
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
10. Telescopic sensor M48
11.
Seat memory switch D5
12. Door mirror remote control switch
D17
A.
Dash side lower (Passenger side)
B.
View with instrument driver lower
panel removed
C.
Backside of seat cushion (driver side)
D.
Behind cluster lid C
E.
AT assembly
(TCM is built in AT assembly)
F.
View with instrument driver lower
panel removed
G
View with steering column cover low-
er and upper removed
13. Front door switch (driver side) B16
14. AT device (detention switch) M137
15. Parking brake switch B14
16. Door mirror (driver side) D3
17. Telescopic motor M49
18. Tilt motor M49
H.
View with center console assembly
removed
I.
View with center console assembly
removed
J.
View with instrument driver lower
panel removed
19. Side support (seat cushion)
(Side support unit B420)
20. Reclining motor B454
21. Side support (seatback)
(Side support unit B420)
22. Side support unit B420
23. Reclining switch
(Power seat switch B459)
24. Sliding, lifting switch
(Power seat switch B459)
25. Side support switch (seat back side)
B419
26. Side support switch (cushion side)
B419
27. Sliding sensor B453
JMJIA0162GB
JMJIA0164GB
ADP-36
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
EXIT ASSIST FUNCTION : Component Description
INFOID:0000000000960606
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
ENTRY ASSIST FUNCTION
28. Lifting motor (front) B455
29. Sliding motor B461
30. Lifting motor (rear) B456
K.
View with seat cushion pad and seat-
back pad removed
L.
Backside of the seat cushion
Item
Function
Driver seat control unit
• Operates the seat sliding motor for a constant amount.
• Requests the operations of tilt motor and telescopic motor to automatic drive po-
sitioner control unit.
Automatic drive positioner control unit
Operates the tilt motor and telescopic motor with the request from the driver seat
control.
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
• Driver door: OPEN/CLOSE
Item
Function
Front door switch (driver side)
Detect front door (driver side) open/close status.
Item
Function
Tilt and telescopic sensor
Detect the up/down and left/right position of steering column.
Sliding sensor
Detect the front/rear position of seat.
Item
Function
Tilt and telescopic motor
Move the steering column upward/downward and frontward/rearward.
Sliding motor
Slide the seat frontward/rearward.
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-37
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ENTRY ASSIST FUNCTION : System Diagram
INFOID:0000000000960607
ENTRY ASSIST FUNCTION : System Description
INFOID:0000000000960608
OUTLINE
The seat is in the exiting position when either following condition (A or B) is satisfied, the seat returns from
exiting position to the previous driving position.
NOTE:
• This function is set to OFF before delivery (initial setting).
• Further information for the system setting procedure. Refer to
ADP-11, "SYSTEM SETTING : Description"
.
OPERATION PROCEDURE
1.
A: Turn the ignition switch ON.
B: Turn the ignition switch from OFF to ACC after closing the driver door.
2.
Driver seat and steering column will return from the exiting position to entry position.
OPERATION CONDITION
Satisfy all of the following items. The entry assist function is not performed if these items are not satisfied.
DETAIL FLOW
JMJIA0116GB
Item
Request status
Seat, steering column
The vehicle is not moved after performing the
exit assist function.
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror control switch
• Set switch
• Memory switch
OFF
(Not operated)
AT selector lever (only for AT model)
P position
Parking break (only for MT models)
Applied
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст