Infiniti G35 (V35) Sedan. Manual — part 1407
TM-320
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
31. Install needle bearing in drum support.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
32. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
33. Install high and low reverse clutch assembly in direct clutch.
34. Using a flat-bladed screwdriver, align the drive plate.
35. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5198E
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E
TRANSMISSION ASSEMBLY
TM-321
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CAUTION:
Make sure that portion “A” of high and low reverse clutch
drum protrudes approximately 2 mm (0.08 in) beyond por-
tion “B” of rear sun gear.
36. Install needle bearing in rear carrier assembly.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
37. Install bearing race in rear carrier assembly.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
38. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA2803E
SCIA5175E
SCIA2462E
TM-322
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
39. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
40. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
41. Install mid carrier assembly in rear carrier assembly.
42. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
43. Install seal rings in input clutch assembly.
SCIA2804E
SCIA2805E
SCIA5017E
SCIA5015E
SCIA2470E
TRANSMISSION ASSEMBLY
TM-323
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
44. Install band servo anchor end pin and lock nut in transmission
case.
45. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
46. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
47. Install needle bearing to front sun gear.
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
48. Adjust brake band tilting using a clip so that brake band contacts
front sun gear drum evenly.
SCIA6512E
SCIA5498E
SCIA5014E
SCIA2808E
SCIA5033E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст