Infiniti G35 (V35) Sedan. Manual — part 1406
TM-316
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
28. Install parking actuator support from rear extension (2WD) or
adapter case (AWD).
29. Install needle bearing (1) to rear extension (2WD) or adapter
case (AWD).
CAUTION:
Take care with the direction of needle bearing. Refer to
289, "Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
30. Install rear extension assembly (2WD) or adapter case assembly (AWD) according to the following proce-
dures.
a.
2WD
i.
Install seal rings (1) to output shaft.
ii.
Install parking gear (1) to output shaft (2).
SCIA3423E
SCIA6179J
JPDIA0030ZZ
JPDIA0029ZZ
TRANSMISSION ASSEMBLY
TM-317
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
iii.
Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
iv.
Install bearing race to output shaft.
v.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown in the
figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
vi. Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5030E
SCIA5245E
A
: Start and finish point shall be in
the center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
SCIA5029E
TM-318
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
vii. Tighten rear extension assembly bolts to the specified torque.
b.
AWD
i.
Install seal rings (1) to output shaft.
ii.
Install parking gear (1) to output shaft (2).
iii.
Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
JPDIA0030ZZ
JPDIA0029ZZ
SCIA5030E
TRANSMISSION ASSEMBLY
TM-319
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
iv.
Install bearing race to output shaft.
v.
Install gasket onto transmission case.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc.
from the transmission case and adapter case assembly
mounting surfaces.
• Do not reuse gasket.
vi. Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the adapter
case assembly.
vii. Tighten adapter case assembly bolts (1) to the specified torque.
[With bracket (2).]
SCIA5245E
SCIA5231E
SCIA5186E
3
: Self-sealing bolt
: Bolt
SCIA6910E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст