Infiniti G35 (V35) Sedan. Manual — part 1388
TM-244
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
INSTALLATION
1.
Connect TCM connector (A) and park/neutral position switch
connector (B).
2.
Install A/T assembly harness connector (A) to control valve with
TCM.
3.
Connect TCM connectors (A) and (B).
4.
Install new O-ring (1) in A/T assembly harness connector (A).
JPDIA0018ZZ
JPDIA0019ZZ
JPDIA0016ZZ
JPDIA0015ZZ
CONTROL VALVE WITH TCM
TM-245
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Install bracket (1) to A/T fluid temperature sensor 2 (2).
6.
Install A/T fluid temperature sensor 2 (1) with bracket (2) in con-
trol valve with TCM. Tighten A/T fluid temperature sensor 2 bolt
to the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
7.
Install control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole (B).
• Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve (1) cutout is engaged
with manual plate (2) projection.
JPDIA0014ZZ
: Bolt
JPDIA0013ZZ
A
: Brake band
JPDIA0020ZZ
JPDIA0012ZZ
TM-246
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
8.
Install bolts A, B and C in control valve with TCM.
9.
Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3), and then tighten other
bolts. Tighten control valve with TCM bolts to the specified
torque.
10. Connect A/T fluid temperature sensor 2 connector (A).
11. Engage terminal cord assembly and A/T fluid temperature sen-
sor 2 harness with terminal clips (
).
12. Connect revolution sensor connector (A).
13. Engage revolution sensor harness with terminal clip (
).
14. Install magnets (1) in oil pan.
15. Install oil pan gasket to oil pan.
CAUTION:
• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
• Complete remove all moisture, oil and old gasket, etc.
from oil pan gasket mounting surface.
: Vehicle front
Bolt symbol
Length
mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
: Vehicle front
SCIA8075E
SCIA8124E
JPDIA0011ZZ
JPDIA0009ZZ
CONTROL VALVE WITH TCM
TM-247
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
16. Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
CAUTION:
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
17. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque.
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan. Tighten drain plug to the specified
torque.
CAUTION:
Do not reuse drain plug gasket.
19. Pull up A/T assembly harness connector (A).
CAUTION:
Be careful not to damage connector.
20. Install snap ring (1) to A/T assembly harness connector (A).
21. Connect A/T assembly harness connector.
: Vehicle front
: Oil pan mounting bolt
: Vehicle front
SCIA8117E
JPDIA0021ZZ
JPDIA0022ZZ
JPDIA0023ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст