Infiniti G35 (V35) Sedan. Manual — part 1389
TM-248
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
22. Install bracket (2) to transmission assembly.
23. Install heated oxygen sensor 2 harness (B) to clips (1).
24. Connect heated oxygen sensor 2 harness connector (A).
25. Install exhaust mounting bracket. Refer to
.
26. Pour ATF into A/T assembly. Refer to
.
27. Connect the battery cable to the negative terminal.
Inspection
INFOID:0000000000957154
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
.
INSPCTION AFTER INSTALLATION
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
: Vehicle front
: Bolt
SCIA8269E
SCIA5199E
A/T FLUID TEMPERATURE SENSOR 2
TM-249
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
A/T FLUID TEMPERATURE SENSOR 2
Exploded View
INFOID:0000000000957155
Removal and Installation
INFOID:0000000000957156
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust mounting bracket. Refer to
4.
Disconnect heated oxygen sensor 2 harness connectors (A).
5.
Remove heated oxygen sensor 2 harness (B) from clips (1).
6.
Remove bracket (2) from transmission assembly.
1.
A/T
2.
Bracket
3.
Bracket
4.
A/T fluid temperature sensor 2
5.
Clip
6.
Oil pan mounting bolt
7.
Oil pan
8.
Magnet
9.
Drain plug
10. Drain plug gasket
11.
Oil pan gasket
Refer to
JSDIA0123GB
: Vehicle front
: Bolt
SCIA8269E
TM-250
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
A/T FLUID TEMPERATURE SENSOR 2
7.
Remove clips (1).
8.
Remove oil pan (2) and oil pan gasket.
9.
Remove magnets (1) from oil pan.
10. Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Be careful not to damage connector.
11. Disengage terminal clip (
).
12. Remove A/T fluid temperature sensor 2 (1) with bracket (2) from
control valve with TCM.
13. Remove bracket (1) from A/T fluid temperature sensor 2 (2).
3
: Drain plug
: Vehicle front
: Oil pan mounting bolt
SCIA8117E
JPDIA0009ZZ
SCIA8125E
: Bolt
JPDIA0025ZZ
JPDIA0014ZZ
A/T FLUID TEMPERATURE SENSOR 2
TM-251
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSTALLATION
1.
Install bracket (1) to A/T fluid temperature sensor 2 (2).
2.
Install A/T fluid temperature sensor 2 (1) with bracket (2) in con-
trol valve with TCM. Tighten A/T fluid temperature sensor 2 bolts
to the specified torque.
3.
Connect A/T fluid temperature sensor 2 connector (A).
4.
Engage A/T fluid temperature sensor 2 harness with terminal
clip (
).
5.
Install magnets (1) in oil pan.
6.
Install oil pan gasket to oil pan.
CAUTION:
• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
• Complete remove all moisture, oil and old gasket, etc.
from oil pan gasket mounting surface.
JPDIA0014ZZ
: Bolt
JPDIA0025ZZ
SCIA8125E
JPDIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст