Infiniti G35 (V35) Sedan. Manual — part 1390
TM-252
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
A/T FLUID TEMPERATURE SENSOR 2
7.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
CAUTION:
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
8.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque.
CAUTION:
Do not reuse oil pan mounting bolts.
9.
Install drain plug to oil pan. Tighten drain plug to the specified
torque.
CAUTION:
Do not reuse drain plug gasket.
10. Install bracket (2) to transmission assembly.
11. Install heated oxygen sensor 2 harness (B) to clips (1).
12. Connect heated oxygen sensor 2 harness connector (A).
13. Install exhaust mounting bracket. Refer to
.
14. Pour ATF into A/T assembly. Refer to
.
15. Connect the battery cable to the negative terminal.
Inspection
INFOID:0000000000957157
INSPECTION AFTER REMOVAL
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
.
INSPECTION AFTER INSTALLATION
After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to
.
: Vehicle front
: Oil pan mounting bolt
SCIA8117E
: Vehicle front
: Vehicle front
: Bolt
JPDIA0021ZZ
SCIA8269E
SCIA5199E
PARKING COMPONENTS
TM-253
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PARKING COMPONENTS
2WD
2WD : Exploded View
INFOID:0000000000957158
2WD : Removal and Installation
INFOID:0000000000957159
REMOVAL
1.
Drain ATF through drain plug.
2.
Remove exhaust front tube and center muffler with power tool. Refer to
.
3.
Remove rear propeller shaft. Refer to
4.
Remove control rod. Refer to
.
5.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6.
Remove rear engine mounting member with power tool. Refer to
7.
Remove engine mounting insulator (rear). Refer to
1.
Rear oil seal
2.
Rear extension
3.
Parking actuator support
4.
Return spring
5.
Parking pawl
6.
Pawl shaft
7.
Self-sealing bolt
8.
Seal ring
9.
Parking gear
10.
Output shaft
11.
Bearing race
12. Needle bearing
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
SCIA8364E
TM-254
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
8.
Remove tightening bolts for rear extension assembly and trans-
mission case.
9.
Tap rear extension assembly with a soft hammer (A).
10. Remove rear extension assembly (with needle bearing) from
transmission case.
11. Remove bearing race (1) from output shaft (2).
12. Remove output shaft (1) from transmission case by rotating left/
right.
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
JPDIA0027ZZ
SCIA3431E
JPDIA0057ZZ
JPDIA0028ZZ
PARKING COMPONENTS
TM-255
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
13. Remove parking gear (1) from output shaft (2).
14. Remove seal rings (1) from output shaft.
15. Remove needle bearing (1) from rear extension.
16. Remove parking actuator support (1) from rear extension.
17. Remove parking pawl (with return spring) (1) and pawl shaft (2)
from rear extension.
JPDIA0029ZZ
JPDIA0030ZZ
SCIA6179J
JPDIA0031ZZ
JPDIA0032ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст