Infiniti G35 (V35) Sedan. Manual — part 1385
TM-232
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL DEVICE
ON-VEHICLE REPAIR
CONTROL DEVICE
2WD
2WD : Exploded View
INFOID:0000000000957138
2WD : Removal and Installation
INFOID:0000000000957139
REMOVAL
1.
Disconnect lower lever of control device and control rod.
2.
Move selector lever to “N” position.
1.
Selector lever knob
2.
Lock pin
3.
Console finisher
4.
Selector lever position indicator
5.
Insert finisher
6.
Dust cover plate
7.
Dust cover
8.
Snap pin
9.
Plain washer
10.
Collar
11.
Control rod
12.
Pivot pin
13.
Insulator
14.
Shift lock unit
15.
Control device assembly
Refer to
for symbols in the figure.
JPDIA0001GB
CONTROL DEVICE
TM-233
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Remove knob cover (A) below selector lever downward.
4.
Pull lock pin (1) out of selector lever knob (2).
5.
Remove selector lever knob (2).
6.
Remove console finisher assembly, rear upper console assem-
bly and front console bracket. Refer to
7.
Remove the center console assembly (with rear ventilator).
Refer to
.
8.
Remove the rear ventilator duct 2 (with rear ventilator). Refer to
VTL-53, "REAR FLOOR DUCT 1 & REAR VENTILATOR DUCT
1(WITH REAR VENTILATOR) : Exploded View"
9.
Disconnect A/T device harness connector.
10. Remove control device assembly.
11. Remove the following parts if necessary.
a.
Selector lever position indicator
i.
Remove the cigarette lighter harness connector (A) from the
console finisher assembly.
ii.
Remove the insert finisher (1) from the console finisher.
iii.
Remove the selector lever position indicator.
b.
Shift lock unit
i.
Remove the shift lock unit from the control device assembly.
INSTALLATION
Install in the reverse order of removal.
2WD : Inspection and Adjustment
INFOID:0000000000957140
ADJUSTMENT AFTER INSTALLATION
Adjust the A/T positions after installing the control device. Refer to
TM-230, "2WD : Inspection and Adjust-
INSPECTION AFTER INSTALLATION
Check the A/T positions after adjusting the A/T positions. Refer to
TM-230, "2WD : Inspection and Adjust-
AWD
AWD : Exploded View
INFOID:0000000000957141
: Screw
JPDIA0002ZZ
JPDIA0050ZZ
TM-234
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
CONTROL DEVICE
AWD : Removal and Installation
INFOID:0000000000957142
REMOVAL
1.
Disconnect lower lever of control device and control rod.
2.
Move selector lever to “N” position.
1.
Selector lever knob
2.
Lock pin
3.
Console finisher
4.
Selector lever position indicator
5.
Insert finisher
6.
Control rod
7.
Dust cover
8.
Dust cover plate
9.
Snap pin
10.
Plain washer
11.
Collar
12. Bracket
13.
Insulator
14.
Shift lock unit
15. Control device assembly
Refer to
for symbols in the figure.
JPDIA0003GB
CONTROL DEVICE
TM-235
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Remove knob cover (A) below selector lever downward.
4.
Pull lock pin (1) out of selector lever knob (2).
5.
Remove selector lever knob (2).
6.
Remove console finisher assembly, rear upper console assem-
bly and console front bracket. Refer to
7.
Remove center console assembly. Refer to
.
8.
Remove the rear ventilator duct 2 (with rear ventilator). Refer to
VTL-53, "REAR FLOOR DUCT 1 & REAR VENTILATOR DUCT
1(WITH REAR VENTILATOR) : Exploded View"
9.
Disconnect A/T device harness connector.
10. Move selector lever to “P” position.
11. Move passenger’s seat to the end.
12. Remove control device assembly mounting dolts.
13. Slightly lift the control device assembly (1) and slide it rightward.
Then pull it out in the diagonally right direction.
14. Remove the following parts if necessary.
a.
Selector lever position indicator
i.
Remove the cigarette lighter harness connector (A) from the
console finisher.
ii.
Remove the insert finisher (1) from the console finisher.
iii.
Remove the selector lever position indicator.
b.
Shift lock unit
i.
Remove the shift lock unit from the control device assembly.
INSTALLATION
Install in the reverse order of removal.
AWD : Inspection and Adjustment
INFOID:0000000000957143
ADJUSTMENT AFTER INSTALLATION
Adjust the A/T positions after installing the control device. Refer to
TM-230, "AWD : Inspection and Adjust-
INSPECTION AFTER INSTALLATION
Check the A/T positions after adjusting the A/T positions. Refer to
TM-230, "AWD : Inspection and Adjust-
JPDIA0002ZZ
JPDIA0055ZZ
: Screw
JPDIA0050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст