Infiniti G35 (V35) Sedan. Manual — part 984
PB-2
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000000958480
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
PARKING BRAKE SYSTEM
PB-3
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
ON-VEHICLE MAINTENANCE
PARKING BRAKE SYSTEM
PEDAL TYPE
PEDAL TYPE : Inspection and Adjustment
INFOID:0000000000958481
INSPECTION
Pedal Stroke
• Operate the parking brake pedal with a force of 196 N (20 kg, 44 lb). Check that the pedal stroke is within the
specified number of notches. (Check it by listening to clicks of ratchet.)
• When parking brake warning lamp turns ON, check that the pedal stroke is within the specified number of
notches. (Check it by listening to clicks of ratchet.)
Inspect Components
• Check each component for installation condition such as looseness.
• Check the device assembly for bend, damage and cracks. Replace if necessary.
• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.
• Check the parking brake switch, and replace it if necessary. Refer to
BRC-69, "Component Inspection"
ADJUSTMENT
• To perform adjustment operations, remove rear tires with power tool.
1.
Fix the disc rotor using wheel nuts.
2.
Release the parking brake pedal by turning the adjusting nut (1)
with a deep socket wrench and loosening the cable.
3.
Remove the adjusting hole plug from the disc rotor. Turn the
adjuster (1) in the direction (A) as shown in the figure using a
suitable tool until the disc rotor is locked.
4.
Turn back the adjuster 5 or 6 notches from the locked position.
5.
Rotate the disc rotor to check that there is no drag. Install the
adjusting hole plug.
6.
Adjust the cable with the following procedure.
a.
Operate the parking brake pedal with a force of 490 N (50 kg,
110 lb) for 10 strokes or more.
b.
Adjust the parking brake pedal stroke by turning the adjusting
nut with a deep socket wrench.
CAUTION:
Never reuse the adjusting nut if the nut is removed.
c.
Operate the parking brake pedal with a force of 196 N (20 kg, 44 lb). Check that the pedal stroke is within
the specified number of notches. (Check it by listening to clicks of ratchet.)
Standard
Number of notches
: Refer to
PB-12, "Parking Brake Control"
Standard
Number of notches
: Refer to
PB-12, "Parking Brake Control"
JPFIB0001ZZ
JPFIB0002ZZ
PB-4
< ON-VEHICLE MAINTENANCE >
PARKING BRAKE SYSTEM
d.
Rotate the disc rotor with the parking brake pedal released and check that there is no drag.
LEVER TYPE
LEVER TYPE : Inspection and Adjustment
INFOID:0000000000958482
INSPECTION
Lever Stroke
• Operate the parking brake lever with a force of 196 N (20 kg, 44 lb). Check that the lever stroke is within the
specified number of notches. (Check it by listening to the clicks of the ratchet.)
• When parking brake warning lamp turns ON, check that the lever stroke is within the specified number of
notches. (Check it by listening to the clicks of the ratchet.)
Inspect Components
• Check each component for installation condition such as looseness.
• Check the device assembly for bend, damage and cracks. Replace if necessary.
• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.
• Check the parking brake switch, and replace it if necessary. Refer to
BRC-69, "Component Inspection"
ADJUSTMENT
• To perform adjustment operations, remove rear tires with power tool.
1.
Fix the disc rotor using wheel nuts.
2.
Remove the coin pocket.
3.
Release the parking brake lever by turning the adjusting nut (1)
with a deep socket wrench and loosening the cable.
4.
Remove the adjusting hole plug from the disc rotor. Turn the
adjuster (1) in the direction (A) as shown in the figure using a
suitable tool until the disc rotor is locked.
5.
Turn back the adjuster 5 or 6 notches from the locked position.
6.
Rotate the disc rotor to check that there is no drag. Install the
adjusting hole plug.
7.
Adjust the cable with the following procedure.
a.
Operate the parking brake lever with a force of 294 N (30 kg, 66
lb) for 10 strokes or more.
b.
Adjust the parking brake lever stroke by turning the adjusting nut
with a deep socket wrench.
CAUTION:
Standard
Number of notches
: Refer to
PB-12, "Parking Brake Control"
Standard
Number of notches
: Refer to
PB-12, "Parking Brake Control"
Standard
Number of notches
: Refer to
PB-12, "Parking Brake Control"
JPFIB0003ZZ
JPFIB0002ZZ
PARKING BRAKE SYSTEM
PB-5
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
Never reuse the adjusting nut if the nut is removed.
c.
Operate the parking brake lever with a force of 196 N (20 kg, 44lb). Check that the lever stroke is within
the specified number of notches. (Check it by listening to the clicks of the ratchet.)
d.
Rotate the disc rotor with the parking brake lever released and check that there is no drag.
Standard
Number of notches
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст