Infiniti G35 (V35) Sedan. Manual — part 1409
TM-328
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
59. Connect TCM connector (A) and park/neutral position switch
connector (B).
60. Install A/T assembly harness connector (A) to control valve with
TCM.
61. Connect TCM connectors (A) and (B).
62. Install O-ring (1) to A/T assembly harness connector (A).
63. Install bracket (1) to A/T fluid temperature sensor 2 (2).
JPDIA0018ZZ
JPDIA0019ZZ
JPDIA0016ZZ
JPDIA0015ZZ
JPDIA0014ZZ
TRANSMISSION ASSEMBLY
TM-329
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
64. Install A/T fluid temperature sensor 2 (1) [with bracket (2)] in
control valve with TCM. Tighten A/T fluid temperature sensor 2
bolt to the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
65. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole (B).
• Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
66. Install bolts A, B and C to control valve with TCM.
JPDIA0013ZZ
A
: Brake band
JPDIA0020ZZ
SCIA5035E
: Front
Bolt symbol
Length
mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
TM-330
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
67. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3), and then tighten other
bolts. Tighten control valve bolts to the TCM with specified
torque.
68. Connect A/T fluid temperature sensor 2 connector (A).
69. Engage terminal cord assembly and A/T fluid temperature sen-
sor 2 harness with terminal clips (
).
70. Connect revolution sensor connector (A).
71. Engage revolution sensor harness with terminal clip (
).
72. Pull down A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
73. Install snap ring to A/T assembly harness connector.
: Front
SCIA8078E
SCIA8124E
JPDIA0011ZZ
SCIA5299E
SCIA5300E
TRANSMISSION ASSEMBLY
TM-331
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
74. Install magnets (1) in oil pan.
75. Install oil pan gasket to transmission case.
CAUTION:
• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
• Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
76. Install oil pan (2) and clips (1) to transmission case.
CAUTION:
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
77. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Tighten oil pan mounting bolts to the specified torque.
CAUTION:
Do not reuse oil pan mounting bolts.
78. Install drain plug to oil pan. Tighten drain plug to the specified
torque.
CAUTION:
Do not reuse drain plug gasket.
79. Pour ATF into torque converter.
• Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.
• When reusing old torque converter, add the same amount
of ATF as was drained.
JPDIA0009ZZ
: Front
: Oil pan mounting bolt
SCIA8117E
: Front
JPDIA0021ZZ
SAT428DA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст