Infiniti G35 (V35). Manual — part 647
MT-56
TRANSMISSION ASSEMBLY
13. Install washer to the withdrawal lever ball pin and then install it
to front cover. Tighten withdrawal lever ball pin to the specified
torque. Refer to
14. Install rear extension oil gutter to rear extension, and then tighten bolt to specified torque. Refer to
.
15. Install reverse idler shaft, reverse idler needle bearing, reverse idler gear, and reverse idler thrust washer
to the adapter plate.
16. Apply multi -purpose grease to the striking rod oil seal lip, and
then using the drift to install striking rod oil seal.
CAUTION:
●
Do not reuse striking rod oil seal.
●
When installing, do not incline the striking rod oil seal.
17. Apply multi - purpose grease to the lip of the rear oil seal. Using
a drift, to install rear oil seal. 1.2-2.2 mm (0.047-0.087 in) above
from the rear extension edge surface.
CAUTION:
●
Do not reuse rear oil seal.
●
When installing, do not incline the rear oil seal.
18. Apply liquid gasket to the adapter plate rear extension mounting
surface as shown in the figure.
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
.
CAUTION:
Completely remove all moisture, oil, etc., from the adapter
plate and rear extension mounting surfaces.
PCIB0456E
Tool number
: ST35291000 (
—
)
PCIB0213E
Tool number
: ST33400001 (J-26082)
PCIB0619E
PCIB1374E
TRANSMISSION ASSEMBLY
MT-57
D
E
F
G
H
I
J
K
L
M
A
B
MT
19. Install rear extension to adapter plate and then tighten mounting
bolts to the specified torque in order as shown on the figure.
Refer to
.
20. Install control lever housing to the rear extension and then
tighten mounting bolts to the specified torque. Refer to
CAUTION:
Do not hold control lever housing to prevent bushing of
control lever housing from deformation when moving trans-
mission assembly.
21. Install return spring plungers and return springs into the rear
extension, apply liquid gasket to the return spring plug threads,
and then tighten return spring plug to the specified torque. Refer
to
MT-24, "Shift Control Components"
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
CAUTION:
The right and left return spring and return spring plunger are different, so make sure they are
installed correctly.
22. Install shift check pin as a one unit with the control bracket to
rear extension and then tighten mounting bolts to the specified
torque. Refer to
MT-24, "Shift Control Components"
23. Install plunger to the rear extension, and then screwing PNP
switch and back-up lamp switch to the rear extension with 1-2
pitches. Apply liquid gasket to the switch threads, and tighten
switch to the specified torque. Refer to
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
24. Install retaining pin into the control rod, using a pin punch [6 mm
(0.24 in) dia.].
CAUTION:
Do not reuse retaining pin.
PCIB0256E
Region
Return spring identification mark
Plunger notch
RH
Brown
No
LH
Blue
Yes
SCIA1607E
SCIA1440E
SCIA1437E
MT-58
TRANSMISSION ASSEMBLY
25. Install check ball and check select spring into the rear extension.
26. Install rear extension upper cover gasket and rear extension
upper cover to rear extension.
CAUTION:
●
Do not reuse rear extension upper cover gasket.
●
Avoid tangling check select spring.
27. Tighten rear extension upper cover bolts to the specified torque
in order as shown on the figure. Refer to
PCIB0599E
PCIB0257E
SERVICE DATA AND SPECIFICATIONS (SDS)
MT-59
D
E
F
G
H
I
J
K
L
M
A
B
MT
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
NCS000AV
End Play
NCS000AW
Unit: mm (in)
Applied model
VQ35DE
Transmission
FS6R31A
Model code number
CD009
Number of speed
6
Shift pattern
Synchromesh type
Warner
Gear ratio
1st
3.794
2nd
2.324
3rd
1.624
4th
1.271
5th
1.000
6th
0.794
Reverse
3.446
Main gear
(Number of teeth)
Drive
26
1st
37
2nd
34
3rd
33
4th
31
6th
31
Reverse
42
Counter shaft gear
(Number of teeth)
Drive
32
1st
12
2nd
18
3rd
25
4th
30
6th
48
Reverse
15
Reverse idler gear (Number of teeth)
26
Oil capacity
(US qt, Imp qt)
Approx. 2.9 (3-1/8, 2-1/2)
Remarks
Reverse synchronizer
Installed
Double cone synchronizer
4th
Triple cone synchronizer
1st, 2nd and 3rd
SCIA0955E
Item
Standard
Counter shaft
0 - 0.10 (0 - 0.004)
Main drive gear
0 - 0.10 (0 - 0.004)
Main shaft
0 - 0.10 (0 - 0.004)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст