Infiniti G35 (V35). Manual — part 646
MT-52
TRANSMISSION ASSEMBLY
19. Install interlock pin and check balls to the adapter plate.
CAUTION:
Apply lithium-based grease check ball.
20. Install 3rd-4th fork rod to the adapter plate.
21. Install 3rd-4th fork rod bracket to the 3rd-4th fork rod.
22. Using a pin punch [6 mm (0.24 in) dia.] to tap the retaining pin
into the 3rd-4th fork rod bracket.
CAUTION:
Do not reuse retaining pin.
23. Install check ball, check ball spring into the adapter plate, apply
liquid gasket to the check ball plug threads, and tighten check
ball plug to the specified torque. Refer to
.
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
.
CAUTION:
Apply lithium-based grease check ball.
24. Install 3rd-4th control lever to the adapter plate, and then tighten mounting bolts to the specified torque.
Refer to
MT-24, "Shift Control Components"
.
CAUTION:
Make sure the top and bottom are oriented correctly.
PCIB0146E
PCIB0145E
PCIB0144E
PCIB1352E
TRANSMISSION ASSEMBLY
MT-53
D
E
F
G
H
I
J
K
L
M
A
B
MT
25. Install check balls, check ball springs into the adapter plate,
apply liquid gasket to the check ball plugs threads, and tighten
check ball plugs to the specified torque. Refer to
.
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
CAUTION:
Apply lithium-based grease check ball.
26. Install striking rod to the adapter plate.
27. Install striking lever to the striking rod.
28. Using a pin punch [6 mm (0.24 in) dia.] to tap the retaining pin
into the striking lever.
CAUTION:
Do not reuse retaining pin.
29. Install magnet to the adapter plate.
30. Install baffle plate to the adapter plate, and then tighten mount-
ing bolts to the specified torque. Refer to
Case Components
1.
Install counter front bearing to the transmission case.
2.
Install oil gutter to transmission case.
3.
Install breather to transmission.
CAUTION:
Do not reuse breather.
PCIB0143E
PCIB0414E
PCIB0154E
PCIB0436E
MT-54
TRANSMISSION ASSEMBLY
4.
Apply liquid gasket to the transmission case adapter plate
mounting surface as shown in the figure.
●
Use Genuine Silicone RTV or equivalent. Refer to
"RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS"
.
CAUTION:
Complete remove all moisture and oil, etc., from the trans-
mission case and adapter plate mounting surfaces.
5.
Place the adapter plate in the transmission case, using a soft
hammer to tap the adapter plate to install it into the transmission
case.
6.
Install snap ring to main drive gear bearing, using snap ring pli-
ers.
CAUTION:
Do not reuse snap ring.
7.
Tighten baffle plate mounting nut to the specified torque. Refer
to
PCIB1373E
SCIA1436E
SCIA1532E
SCIA1443E
TRANSMISSION ASSEMBLY
MT-55
D
E
F
G
H
I
J
K
L
M
A
B
MT
8.
Apply multi-purpose grease to the lip of the front cover oil seal.
Using a drift, to install oil seal approx. 8.55-9.55 mm (0.336-
0.376 in) above from the front cover edge surface.
CAUTION:
●
Do not reuse front cover oil seal.
●
When installing, do not incline the front cover oil seal.
9.
Install front cover gasket and front cover to the transmission
case.
CAUTION:
Do not reuse front cover gasket.
10. Temporary tightening 2 bolts in the positions shown in the figure.
11. Temporary tightening remaining 9 bolts.
CAUTION:
Four bolts pointed by arrows in the figure are not reusable.
12. Tighten bolts to the specified torque in order as shown on the
figure. Refer to
.
Tool number
: KV38102100 (J-25803-01)
PCIB0415E
PCIB0454J
PCIB0455J
PCIB0258E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст