Infiniti G35 (V35). Manual — part 81
ASSEMBLY
AT-315
D
E
F
G
H
I
J
K
L
M
A
B
AT
d.
Install O-ring to A/T assembly harness connector.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
e.
Install A/T fluid temperature sensor 2 to bracket.
f.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM, and then tighten A/T fluid temperature sensor 2
mounting bolt to the specified torque. Refer to
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
g.
Install control valve with TCM in transmission case.
CAUTION:
●
Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.
●
Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
●
Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
SCIA5155E
SCIA5264E
SCIA5301E
SCIA5034E
AT-316
ASSEMBLY
●
Assemble it so that manual valve cutout is engaged with
manual plate projection.
h.
Install bolts A, B and C to control valve with TCM.
●
: Front
i.
Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3), and then tighten other
bolts to the specified torque. Refer to
●
: Front
10. Connect A/T fluid temperature sensor 2 connector (A).
11. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
●
: Terminal clip (4)
12. Connect revolution sensor connector.
SCIA5035E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
SCIA8078E
SCIA8124E
SCIA7524E
ASSEMBLY
AT-317
D
E
F
G
H
I
J
K
L
M
A
B
AT
13. Securely fasten revolution sensor harness with terminal clip.
14. Pull down A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
15. Install snap ring to A/T assembly harness connector.
16. Install magnets in oil pan.
17. Install oil pan to transmission case.
a.
Install oil pan gasket to transmission case.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
SCIA7526E
SCIA5299E
SCIA5300E
SCIA5200E
AT-318
ASSEMBLY
b.
Install oil pan (2) and clips (1) to transmission case.
CAUTION:
●
Install it so that drain plug (3) comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Complete remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer
.
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan, and then tighten drain plug to the
specified torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
19. Install torque converter.
a.
Pour ATF into torque converter.
●
Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.
●
When reusing old torque converter, add the same amount
of ATF as was drained.
b.
Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
c.
Measure distance “A” to check that torque converter is in proper
position.
SCIA8117E
SCIA4113E
SAT428DA
SCIA5010E
Distance “A”:
25.0 mm (0.98 in) or more
SAT017B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст