Infiniti G35 (V35). Manual — part 79
ASSEMBLY
AT-307
D
E
F
G
H
I
J
K
L
M
A
B
AT
CAUTION:
Check that portion “A” of high and low reverse clutch drum
protrudes approximately 2 mm (0.08 in) beyond portion “B”
of rear sun gear.
42. Install needle bearing in rear carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
43. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
44. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA2803E
SCIA5175E
SCIA2462E
AT-308
ASSEMBLY
45. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
46. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
●
Apply petroleum jelly to needle bearing.
47. Install mid carrier assembly in rear carrier assembly.
48. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
49. Install seal rings in input clutch assembly.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
SCIA2804E
SCIA2805E
SCIA5017E
SCIA5015E
SCIA2470E
ASSEMBLY
AT-309
D
E
F
G
H
I
J
K
L
M
A
B
AT
50. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
51. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
52. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
53. Install needle bearing to front sun gear.
CAUTION:
●
Take care with the direction of needle bearing. Refer to
AT-262, "Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
●
Apply petroleum jelly to needle bearing.
54. Adjust brake band tilting using clips so that brake band contacts
front sun gear drum evenly.
SCIA6512E
SCIA5498E
SCIA5014E
SCIA2808E
SCIA5033E
AT-310
ASSEMBLY
55. Adjust brake band.
a.
Loosen lock nut.
b.
Tighten band servo anchor end pin to the specified torque.
c.
Back of band servo anchor end pin three turns.
d.
Holding band servo anchor end pin, and then tighten lock nut to
the specified torque. Refer to
.
Adjustment
NCS000JC
TOTAL END PLAY
●
Measure clearance between front sun gear and bearing race for
oil pump cover.
●
Select proper thickness of bearing race so that end play is within
specifications.
1.
Measure dimensions “K” and “L” and then calculate dimension
“J”.
a.
Measure dimension “K”.
: 5.0 N·m (0.51 kg-m, 44 in-lb)
SCIA5498E
SCIA2810E
SCIA7073E
SCIA7074E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст