Infiniti G35 (V35). Manual — part 64
ON-VEHICLE SERVICE
AT-247
D
E
F
G
H
I
J
K
L
M
A
B
AT
INSTALLATION
CAUTION:
After completing installation, check A/T position, A/T fluid leakage and A/T fluid level. Refer to
1.
Install revolution sensor in transmission case, and then tighten
revolution sensor mounting bolt to the specified torque. Refer to
.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
2.
Connect revolution sensor connector.
3.
Securely fasten revolution sensor harness with clip.
4.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-46, "Recommended Chemical Prod-
.) to rear extension assembly as shown in
the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from transmission case and rear extension assembly
mounting surfaces.
SCIA3997E
SCIA7524E
SCIA7525E
SCIA8228E
AT-248
ON-VEHICLE SERVICE
5.
Install rear extension assembly to transmission case. (With nee-
dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
6.
Tighten rear extension assembly mounting bolts to specified
torque. Refer to
.
CAUTION:
Do not reuse self-sealing bolts.
7.
Install rear engine mounting member. Refer to
.
8.
Install oil pan to transmission case.
a.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan gasket mounting surface.
b.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
●
: Vehicle front
●
: Bolt (22)
CAUTION:
●
Install it so that drain plug (3) comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to
CAUTION:
Do not reuse oil pan mounting bolts.
9.
Install drain plug to oil pan, and then tighten drain plug to the
specified torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
10. Install control rod. Refer to
AT-215, "Control Rod Removal and
SCIA3431E
SCIA6941E
SCIA6257E
SCIA8117E
SCIA4113E
ON-VEHICLE SERVICE
AT-249
D
E
F
G
H
I
J
K
L
M
A
B
AT
11. Install rear propeller shaft. Refer to
PR-4, "Removal and Installation"
.
12. Install exhaust front tube and center muffler. Refer to
EX-3, "Removal and Installation"
.
13. Pour ATF into A/T assembly. Refer to
.
14. Connect the battery cable to the negative terminal.
AT-250
AIR BREATHER HOSE
AIR BREATHER HOSE
PFP:31098
Removal and Installation
NCS000IZ
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, be careful not to be crushed or blocked by folding or bend-
ing the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend R portion.
●
When inserting a hose to the air breather tube, be sure to insert it fully until its end reaches the
tube spool portion.
SCIA6486E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст