Infiniti G35 (V35). Manual — part 63
ON-VEHICLE SERVICE
AT-243
D
E
F
G
H
I
J
K
L
M
A
B
AT
13. Install engine mounting insulator (rear). Refer to
14. Install rear engine mounting member. Refer to
15. Install rear propeller shaft. Refer to
16. Install control rod. Refer to
AT-215, "Control Rod Removal and
.
17. Install exhaust front tube and center muffler. Refer to
18. Install drain plug to oil pan, and then tighten drain plug to the
specified torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
19. Pour ATF into A/T assembly. Refer to
.
Rear Oil Seal
NCS000IX
REMOVAL
1.
Remove exhaust front tube and center muffler with power tool.
Refer to
EX-3, "Removal and Installation"
2.
Remove rear propeller shaft. Refer to
.
3.
Remove rear oil seal using a flat-bladed screwdriver.
CAUTION:
Be careful not to scratch rear extension assembly.
INSTALLATION
CAUTION:
After completing installation, check A/T fluid leakage and A/T fluid level. Refer to
,
1.
As shown in the figure, use the drift to drive rear oil seal into rear
extension assembly until it is flush.
CAUTION:
●
Do not reuse rear oil seal.
●
Apply ATF to rear oil seal.
2.
Install rear propeller shaft. Refer to
3.
Install exhaust front tube and center muffler. Refer to
SCIA6258E
SCIA6257E
SCIA3428E
SCIA5310E
AT-244
ON-VEHICLE SERVICE
Revolution Sensor
NCS000IY
COMPONENTS
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust front tube and center muffler with power tool. Refer to
EX-3, "Removal and Installation"
.
4.
Remove rear propeller shaft. Refer to
PR-4, "Removal and Installation"
5.
Remove control rod. Refer to
AT-215, "Control Rod Removal and Installation"
.
1.
Rear extension
2.
A/T
3.
Oil pan gasket
4.
Clip
5.
Oil pan mounting bolt
6.
Oil pan
7.
Drain plug
8.
Drain plug gasket
9.
Revolution sensor
10.
Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
However, refer to the following symbols for others.
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-46, "Recommended Chemical Products and Seal-
SCIA8043E
ON-VEHICLE SERVICE
AT-245
D
E
F
G
H
I
J
K
L
M
A
B
AT
6.
Remove clips (1).
7.
Remove oil pan (2) and oil pan gasket.
●
: Vehicle front
●
: Bolt (22)
●
Drain plug (3)
8.
Check foreign materials in oil pan to help determine causes of
malfunction. If the ATF is very dark, smells burned, or contains
foreign particles, the frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.
●
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
AT-14, "A/T Fluid Cooler Cleaning"
.
9.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to prevent from damaging control valve
with TCM and transmission case.
10. Remove rear engine mounting member with power tool. Refer to
AT-251, "Removal and Installation"
.
11. Remove tightening bolts for rear extension assembly and trans-
mission case.
SCIA8117E
SCIA5199E
SCIA6257E
SCIA6941E
AT-246
ON-VEHICLE SERVICE
12. Tap rear extension assembly with a soft hammer.
13. Remove rear extension assembly from transmission case. (With
needle bearing.)
14. Disconnect revolution sensor connector.
CAUTION:
Be careful not to damage connector.
15. Straighten terminal clip to free revolution sensor harness.
16. Remove revolution sensor from transmission case.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
SCIA3432E
SCIA3431E
SCIA7524E
SCIA7525E
SCIA3997E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст