Infiniti G35 (V35). Manual — part 709
RSU-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Cautions
NES0002H
●
When installing rubber bushings, final tightening must be carried out under unladen conditions with tires
on level ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
–
Unladen conditions means that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
●
After servicing suspension parts, be sure to check wheel alignment.
●
Caulking nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.
PREPARATION
RSU-3
C
D
F
G
H
I
J
K
L
M
A
B
RSU
PREPARATION
PFP:00002
Special Service Tools
NES0002I
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NES0002J
Tool number
(Kent-Moore No.)
Tool name
Description
ST3127S000
(J-25765-A)
Preload gauge
Measuring rotating torque of ball joint
ZZA0806D
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
RSU-4
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
NES0002K
Use chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in
PR
s
e
c
ti
o
n
.
NVH i
n
RFD s
e
c
tio
n
.
NVH
in
RAX
a
n
d
RS
U
s
e
c
ti
o
n
s
.
NVH
in
W
T
s
e
c
ti
o
n
.
NVH
in
W
T
s
e
c
ti
o
n
.
NVH i
n
RAX s
e
c
tio
n
.
NVH in
BR
s
e
c
ti
o
n
.
NVH in
PS
s
e
c
ti
o
n
.
Possible cause and SUSPECTED PARTS
Im
pr
o
per
i
n
st
al
la
ti
on
, l
o
osen
ess
Sho
ck abs
or
b
e
r def
or
m
a
ti
on
, dam
ag
e
o
r def
le
ct
io
n
Bus
h
ing or
m
oun
ti
ng det
er
io
ra
ti
on
P
a
rt
s
in
te
rf
e
re
n
c
e
Spr
ing f
a
ti
gue
Sus
pens
io
n l
o
o
s
ene
ss
In
co
rr
ect
w
h
e
e
l al
ignm
en
t
S
ta
b
ili
z
er
bar
f
a
ti
g
u
e
PROPELL
E
R SHAF
T
DIFFERENTIAL
REAR AXLE AND
RE
AR
SUSPENSION
TIRES
ROAD
W
H
E
E
L
DRIVE SHA
F
T
BRAKES
STEERING
Symptom
REAR SUSPENSION
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
REAR SUSPENSION ASSEMBLY
RSU-5
C
D
F
G
H
I
J
K
L
M
A
B
RSU
REAR SUSPENSION ASSEMBLY
PFP:55020
On-Vehicle Inspection
NES0002L
Make sure the mounting conditions (looseness, back lash) of each component and component status (wear,
damage) are normal.
INSPECTION SUSPENSION ARM BALL JOINT AXIAL END PLAY
Measure axial end play by placing and moving up/down with an iron pry bar or something similar between sus-
pension arm and axle assembly.
CAUTION:
Be careful not to damage ball joint boot.
SHOCK ABSORBER INSPECTION
Check shock absorber for oil leakage, damage and replace if necessary.
Wheel Alignment Inspection
NES000DQ
DESCRIPTION
●
Measure wheel alignment under unladen conditions. “Unladen conditions” means that fuel, engine cool-
ant, and lubricant are full. Spare tire, jack, hand tools and mats in designated positions.
PRELIMINARY INSPECTION
●
Check tires for improper air pressure and wear.
●
Check road wheels for runout.
●
Check wheel bearing axial end play.
●
Check ball joint axial end play of suspension arm.
●
Check shock absorber operation.
●
Check each mounting point of axle and suspension for looseness and deformation.
●
Check each link, arm and member for cracks, deformation, and other damage.
●
Check vehicle posture.
GENERAL INFORMATION AND RECOMMENDATIONS
●
A four-wheel thrust alignment should be performed.
–
This type of alignment is recommended for any NISSAN/INFINITI vehicle.
–
The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel is
centered.
–
The alignment rack itself should be capable of accepting any NISSAN/INFINITI vehicle.
–
The rack should be checked to ensure that it is level.
●
Make sure the machine is properly calibrated.
–
Your alignment equipment should be regularly calibrated in order to give correct information.
–
Check with the manufacturer of your specific equipment for their recommended Service/Calibration
Schedule.
Axial end play
: 0 mm (0 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст