Infiniti G35 (V35). Manual — part 341
DTC P0128 THERMOSTAT FUNCTION
EC-245
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0128 THERMOSTAT FUNCTION
PFP:21200
On Board Diagnosis Logic
NBS000QB
Engine coolant temperature has not risen enough to open the thermostat even though the engine has run long
enough.
This is due to a leak in the seal or the thermostat stuck open.
DTC Confirmation Procedure
NBS000QC
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
●
For best results, perform at ambient temperature of –10
°
C (14
°
F) or higher.
●
For best results, perform at engine coolant temperature of –10
°
C (14
°
F) to 65
°
C (140
°
F).
WITH CONSULT-II
1.
Replace thermostat with new one. Refer to
CO-28, "WATER INLET AND THERMOSTAT ASSEMBLY"
Use only a genuine NISSAN thermostat as a replacement. If an incorrect thermostat is used, the MIL may
come on.
2.
Turn ignition switch ON.
3.
Select “COOLAN TEMP/S” in “DATA MONITOR” mode with
CONSULT-II.
4.
Check that the “COOLAN TEMP/S” is above 65
°
C (140
°
F).
If it is below 65
°
C (140
°
F), go to following step.
If it is above 65
°
C (140
°
F), cool down the engine to less than
65
°
C (140
°
F), then retry from step 1.
5.
Drive vehicle for 10 consecutive minutes under the following
conditions.
If 1st trip DTC is detected, go to
EC-245, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
Diagnostic Procedure
NBS000QD
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
Refer to
EC-246, "Component Inspection"
OK or NG
OK
>> INSPECTION END
NG
>> Replace engine coolant temperature sensor.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0128
0128
Thermostat function
The engine coolant temperature does not
reach to specified temperature even though
the engine has run long enough.
●
Thermostat
●
Leakage from sealing portion of thermo-
stat
●
Engine coolant temperature sensor
VHCL SPEED SE
80 - 120 km/h (50 - 75 MPH)
SEF176Y
EC-246
DTC P0128 THERMOSTAT FUNCTION
Component Inspection
NBS000QE
ENGINE COOLANT TEMPERATURE SENSOR
1.
Check resistance between engine coolant temperature sensor
terminals 1 and 2 as shown in the figure.
<Reference data>
2.
If NG, replace engine coolant temperature sensor.
Removal and Installation
NBS000QF
ENGINE COOLANT TEMPERATURE SENSOR
Refer to
CO-30, "WATER OUTLET AND WATER PIPING"
PBIB2005E
Engine coolant temperature
°
C (
°
F)
Resistance
k
Ω
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
SEF012P
DTC P0130, P0150 A/F SENSOR 1
EC-247
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0130, P0150 A/F SENSOR 1
PFP:22693
Component Description
NBS000YP
The air fuel ratio (A/F) sensor 1 is a planar dual-cell limit current sen-
sor. The sensor element of the A/F sensor 1 is the combination of a
Nernst concentration cell (sensor cell) with an oxygen-pump cell,
which transports ions. It has a heater in the element.
The sensor is capable of precise measurement = 1, but also in the
lean and rich range. Together with its control electronics, the sensor
outputs a clear, continuous signal throughout a wide range (0.7 <
< air).
The exhaust gas components diffuse through the diffusion gap at the
electrode of the oxygen pump and Nernst concentration cell, where
they are brought to thermodynamic balance.
An electronic circuit controls the pump current through the oxygen-
pump cell so that the composition of the exhaust gas in the diffusion
gap remains constant at = 1. Therefore, the A/F sensor 1 is able to
indicate air/fuel ratio by this pumping of current. In addition, a heater
is integrated in the sensor to ensure the required operating tempera-
ture of 700 - 800
°
C (1,292 - 1,472
°
F).
CONSULT-II Reference Value in Data Monitor Mode
NBS000YQ
Specification data are reference values.
On Board Diagnosis Logic
NBS000YR
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the air fuel ratio (A/
F) sensor 1 signal fluctuates according to fuel feedback control.
DTC Confirmation Procedure
NBS000YS
Perform PROCEDURE FOR MALFUNCTION A first.
If the DTC cannot be confirmed, perform PROCEDURE FOR MALFUNCTION B.
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
PROCEDURE FOR MALFUNCTION A
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
SEF579Z
SEF580Z
MONITOR ITEM
CONDITION
SPECIFICATION
A/F SEN1 (B1)
A/F SEN1 (B2)
●
Engine: After warming up
Maintaining engine speed at
2,000 rpm
Fluctuates around 1.5V
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible Cause
P0130
0130
(Bank 1)
Air fuel ratio (A/F) sensor 1
circuit
A)
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly in the range other
than approx. 1.5V.
●
Harness or connectors
(The A/F sensor 1 circuit is open
or shorted.)
●
Air fuel ratio (A/F) sensor 1
P0150
0150
(Bank 2)
B)
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly approx. 1.5V.
EC-248
DTC P0130, P0150 A/F SENSOR 1
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Let engine idle for 2 minutes.
4.
If 1st trip DTC is detected, go to
EC-253, "Diagnostic Procedure"
.
With GST
Follow the procedure “With CONSULT-II” above.
PROCEDURE FOR MALFUNCTION B
CAUTION:
Always drive vehicle at a safe speed.
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “A/F SEN1 (B1)” or “A/F SEN1 (B2)” in “DATA MONITOR” mode with CONSULT-II.
3.
Check “A/F SEN1 (B1)” or “A/F SEN1 (B2)” indication.
If the indication is constantly approx. 1.5V and does not fluctuates, go to
EC-253, "Diagnostic Procedure"
.
If the indication fluctuates around 1.5V, go to next step.
4.
Select “A/F SEN1 (B1) P1276” (for DTC P0130) or “A/F SEN1 (B2) P1286” (for DTC P0150) of “A/F
SEN1” in “DTC WORK SUPPORT” mode with CONSULT-II.
5.
Touch “START”.
6.
When the following conditions are met, “TESTING” will be dis-
played on the CONSULT-II screen.
If “TESTING” is not displayed after 20 seconds, retry from
step 2.
7.
Release accelerator pedal fully.
NOTE:
Never apply brake during releasing the accelerator pedal.
SEF174Y
ENG SPEED
1,100 - 3,200 rpm
VHCL SPEED SE
More than 64 km/h (40 MPH)
B/FUEL SCHDL
1.0 - 8.0 msec
Shift lever
D position (A/T)
5th position (M/T)
SEF576Z
SEF577Z
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст