Infiniti G35 (V35). Manual — part 340
DTC P0125 ECT SENSOR
EC-241
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK THERMOSTAT OPERATION
When the engine is cold [lower than 70
°
C (158
°
F)] condition, grasp lower radiator hose and confirm the engine
coolant does not flow.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace thermostat. Refer to
CO-28, "WATER INLET AND THERMOSTAT ASSEMBLY"
.
4.
CHECK INTERMITTENT INCIDENT
Refer to
EC-151, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
Refer to
>> INSPECTION END
Component Inspection
NBS000Q3
ENGINE COOLANT TEMPERATURE SENSOR
1.
Check resistance between engine coolant temperature sensor
terminals 1 and 2 as shown in the figure.
<Reference data>
2.
If NG, replace engine coolant temperature sensor.
Removal and Installation
NBS000Q4
ENGINE COOLANT TEMPERATURE SENSOR
Refer to
CO-30, "WATER OUTLET AND WATER PIPING"
PBIB2005E
Engine coolant temperature
°
C (
°
F)
Resistance
k
Ω
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
SEF012P
EC-242
DTC P0127 IAT SENSOR
DTC P0127 IAT SENSOR
PFP:22630
Component Description
NBS000Q5
The intake air temperature sensor is built into mass air flow sensor.
The sensor detects intake air temperature and transmits a signal to
the ECM.
The temperature sensing unit uses a thermistor which is sensitive to
the change in temperature. Electrical resistance of the thermistor
decreases in response to the temperature rise.
<Reference data>
*: This data is reference value and is measured between ECM terminal 34 (Intake air
temperature sensor) and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output
voltage. Doing so may result in damage to the ECM's transistor.
Use a ground other than ECM terminals, such as the ground.
On Board Diagnosis Logic
NBS000Q6
DTC Confirmation Procedure
NBS000Q7
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
CAUTION:
Always drive vehicle at a safe speed.
TESTING CONDITION:
This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road
test is expected to be easier, it is unnecessary to lift the vehicle.
WITH CONSULT-II
1.
Wait until engine coolant temperature is less than 90
°
C (194
°
F)
a.
Turn ignition switch ON.
PBIB1604E
Intake air temperature
°
C (
°
F)
Voltage*
V
Resistance
k
Ω
25 (77)
3.3
1.800 - 2.200
80 (176)
1.2
0.283 - 0.359
SEF012P
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0127
0127
Intake air temperature
too high
Rationally incorrect voltage from the sensor is
sent to ECM, compared with the voltage signal
from engine coolant temperature sensor.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Intake air temperature sensor
DTC P0127 IAT SENSOR
EC-243
C
D
E
F
G
H
I
J
K
L
M
A
EC
b.
Select “DATA MONITOR” mode with CONSULT-II.
c.
Check the engine coolant temperature.
d.
If the engine coolant temperature is not less than 90
°
C (194
°
F),
turn ignition switch OFF and cool down engine.
●
Perform the following steps before engine coolant tempera-
ture is above 90
°
C (194
°
F).
2.
Turn ignition switch ON.
3.
Select “DATA MONITOR” mode with CONSULT-II.
4.
Start engine.
5.
Hold vehicle speed at more than 70 km/h (43 MPH) for 100 con-
secutive seconds.
6.
If 1st trip DTC is detected, go to
EC-243, "Diagnostic Procedure"
WITH GST
Follow the procedure “WITH CONSULT-II” above.
Diagnostic Procedure
NBS000Q8
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten two ground screws on the body. Refer to
.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK INTAKE AIR TEMPERATURE SENSOR
Refer to
EC-226, "Component Inspection"
OK or NG
OK
>> GO TO 3.
NG
>> Replace mass air flow sensor (with intake air temperature sensor).
3.
CHECK INTERMITTENT INCIDENT
Refer to
EC-151, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
Refer to
>> INSPECTION END
SEF189Y
PBIB2192E
EC-244
DTC P0127 IAT SENSOR
Component Inspection
NBS000Q9
INTAKE AIR TEMPERATURE SENSOR
1.
Check resistance between intake air temperature sensor termi-
nals 5 and 6 under the following conditions.
2.
If NG, replace mass air flow sensor (with intake air temperature
sensor).
Removal and Installation
NBS000QA
MASS AIR FLOW SENSOR
Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
Intake air temperature
°
C (
°
F)
Resistance k
Ω
25 (77)
1.800 - 2.200
PBIB1604E
SEF012P
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст