Infiniti G35 (V35). Manual — part 61
ON-VEHICLE SERVICE
AT-235
D
E
F
G
H
I
J
K
L
M
A
B
AT
Installation
CAUTION:
After completing installation, check A/T fluid leakage and A/T fluid level. Refer to
,
1.
Install A/T fluid temperature sensor 2 to bracket.
2.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM, and then tighten A/T fluid temperature sensor 2
bolts to the specified torque. Refer to
.
3.
Connect A/T fluid temperature sensor 2 connector (A).
4.
Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip (
).
5.
Install oil pan to transmission case.
a.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
b.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
●
: Vehicle front
●
: Bolt (22)
CAUTION:
●
Install it so that drain plug (3) comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
SCIA5264E
SCIA5302E
SCIA8125E
SCIA8117E
AT-236
ON-VEHICLE SERVICE
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to
CAUTION:
Do not reuse oil pan mounting bolts.
6.
Install drain plug to oil pan, and then tighten drain plug to the
specified torque. Refer to
CAUTION:
Do not reuse drain plug gasket.
7.
Connect heated oxygen sensor 2 harness connector.
8.
Pour ATF into A/T assembly. Refer to
9.
Connect the battery cable to the negative terminal.
Parking Components
NCS000IW
COMPONENTS
SCIA4113E
1.
Rear oil seal
2.
Rear extension
3.
Parking actuator support
4.
Return spring
5.
Parking pawl
6.
Pawl shaft
7.
Self-sealing bolt
8.
Seal ring
9.
Parking gear
10.
Output shaft
11.
Bearing race
12. Needle bearing
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to
However, refer to the following symbols for others.
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-46, "Recommended Chemical Products and Seal-
SCIA7030E
ON-VEHICLE SERVICE
AT-237
D
E
F
G
H
I
J
K
L
M
A
B
AT
REMOVAL
1.
Drain ATF through drain plug.
2.
Remove exhaust front tube and center muffler with power tool. Refer to
EX-3, "Removal and Installation"
3.
Remove rear propeller shaft. Refer to
PR-4, "Removal and Installation"
.
4.
Remove control rod. Refer to
AT-215, "Control Rod Removal and Installation"
5.
Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6.
Remove rear engine mounting member with power tool. Refer to
AT-251, "Removal and Installation"
.
7.
Remove engine mounting insulator (rear). Refer to
8.
Remove tightening bolts for rear extension assembly and trans-
mission case.
9.
Tap rear extension assembly with a soft hammer.
SCIA6257E
SCIA6258E
SCIA6941E
SCIA3432E
AT-238
ON-VEHICLE SERVICE
10. Remove rear extension assembly from transmission case. (With
needle bearing.)
11. Remove bearing race from output shaft.
12. Remove output shaft from transmission case by rotating left/
right.
13. Remove parking gear from output shaft.
14. Remove seal rings from output shaft.
SCIA3431E
SCIA5245E
SCIA5246E
SCIA5247E
SCIA5209E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст