Volkswagen Golf / Golf GTI / Jetta. Manual — part 1167
01-60
Note:
Rapid data transfer
HELP
Control module does not answer!
If this message appears in the
display:
- Press the HELP button to print
out a list of possible malfunction
causes.
- After correcting malfunctions, re-
enter address word 16 for
Steering wheel electronics and
press -Q- button to confirm input.
1JO035152 Radio
0001
Coding 04403
WSC 00000
Indicated on display:
- Press
button.
Rapid data transfer
HELP
Select function XX
Indicated on display (select
function):
Multi-function steering wheel through 11.01, On Board Diagnostic (OBD)
13/2/2005
01-61
List of available functions
Function
page
01 -
Check Control Module
Versions
Page 01-
59
02 -
Check DTC Memory
Page 01-
62
03 -
Output Diagnostic Test Mode
(DTM)
Page 01-
68
05 -
Erase DTC Memory
Page 01-
71
06 -
End Output
Page 01-
73
07 -
Code Control Module
Page 01-
74
08 -
Read Measuring Value Block
Page 01-
76
Notes:
Press the HELP button to print out a complete
list of available functions. This list indicates the
function capability of the VAG 1551 Scan Tool
(ST) only, and does not necessarily reflect the
function capability of vehicle systems equipped
with OBD. For "Steering wheel electronics"
address word 16, do not attempt to select
functions other than those listed above.
After the function is completed and forwarded
with the
button, the VAG 1551 Scan Tool
(ST) returns to the following start position:
Rapid data transfer
HELP
Select function XX
Indicated on display (select function):
Multi-function steering wheel through 11.01, On Board Diagnostic (OBD)
13/2/2005
01-62
Diagnostic Trouble Code (DTC) memory,
checking (function 02)
Note:
DTCs stored in memory along with
corresponding malfunction descriptions can only
be displayed by initiating the On Board
Diagnostic program and checking DTC memory
(function 02).
- Connect VAG 1551 Scan Tool (ST), input
address word 16, "Steering wheel electronics",
and press
button until "Select function XX"
appears in display.
- Switch on printer with the Print button (indicator
lamp in button lights up).
Rapid data transfer
HELP
Select function XX
Indicated on display (select function):
- Press buttons -0- and -2- to select "Check
Diagnostic Trouble Code (DTC) memory"
function 02.
Rapid data transfer
Q
02 - Check DTC memory
Indicated on display:
- Press -Q- button to confirm input.
X DTC recognized!
The number of stored malfunctions appears in the
display.
The number of stored DTCs or "No DTC s
recognized" appears in the display and are printed
out one after another.
- When the last DTC has been displayed and
printed out, correct malfunctions as described in
DTC table
Page 01-64
.
Multi-function steering wheel through 11.01, On Board Diagnostic (OBD)
13/2/2005
01-63
No DTC recognized!
If "No DTC recognized" is displayed,
the program will return to the initial
position after pressing
button.
Rapid data transfer
HELP
Select function XX
Indicated on display (select
function):
If display not indicated as shown:
Scan tool operating instructions
Note:
If DTCs were recognized, follow the
sequence below:
- 1. Correct malfunction.
- 2. Erase Diagnostic Trouble Code
(DTC) memory (function 05).
- 3. Check Diagnostic Trouble Code
(DTC) memory (function 02).
- End Output (function 06)
Page
01-73
.
- Switch off ignition and disconnect
Data Link Connector (DLC).
Multi-function steering wheel through 11.01, On Board Diagnostic (OBD)
13/2/2005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст