Volkswagen Golf / Golf GTI / Jetta. Manual — part 347
01-50
V.A.G 1551
print-out
Possible cause
Repair
01130
ABS
operation
Implausible
signal
1)
Electrical interference
from other sources (high
frequency radiation e.g.
non-insulated ignition
cable)
- Erase DTC memory
- Perform test drive at more than 20
km/h (13 mph)
- Check DTC memory again
Open circuit, short to
positive or Ground in the
wiring
- Check wiring and connections using
wiring diagram
- Perform electrical checks
Page 01-
102
If the malfunction occurs again:
ABS Control Module
(w/EDL) -J104- faulty
Repair Manual, Brake System, Repair
Group 45; Hydraulic unit, brake
booster/brake master cylinder -
Assembly overview; Removing and
installing control module and hydraulic
unit
- Replace ABS control module (w/EDL)
-J104-
1)
Type of DTC; this DTC is only recognized above 20 km/h (13 mph) (carry out test
drive).
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-51
V.A.G 1551
print-out
Possible cause
Repair
01276
ABS
hydraulic
pump
-V64-
Signal
outside
tolerances
1)
ABS hydraulic
pump -V64-
connector to
control module
faulty
- Perform output Diagnostic Test Mode (DTM)
Page 01-74
Open circuit, short
to positive or
Ground in the
wiring
- Check wiring and connections using wiring
diagram
- Perform electrical checks
from
Page
01-102
ABS hydraulic
pump -V64- faulty
- If the ABS hydraulic pump -V64- runs free
while electrical check test step 18 performed
Page 01-102
, replace ABS control module
(w/EDL) -J104-
ABS control
module (w/EDL) -
J104- faulty
Repair Manual, Brake System, Repair
Group 45; Hydraulic unit, brake booster/brake
master cylinder - Assembly overview;
Removing and installing control module and
hydraulic unit
- Replace ABS control module (w/EDL) -
J104-
1)
Type of DTC; this DTC is only recognized above 20 km/h (13 mph) (carry out test
drive).
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-52
V.A.G 1551
print-out
Possible cause
Repair
01312
Drive train data
bus faulty
1)
or:
ABS control module (w/EDL)
-J104- incorrectly coded
Engine control module
incorrectly coded
Repair group 01 for relevant
engine code
- Check ABS control module
(w/EDL) -J104- coding
Page
01-58
- Check engine control module
coding
Open circuit, short to positive
or Ground in the wiring
- Check wiring and connections
using wiring diagram
- Perform electrical checks
Page 01-102
Drive train data
bus faulty
1)
Sporadic
Ignition/starter switch turned
too slowly
- Erase DTC memory
Page
01-56
- No further measures required
- Inform customer
1)
The DTC "Drive train data bus" will not cause the ABS warning light -K47- or warning
light for brake system -K118- to light up. The ABS function is retained over the complete
range.
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
01-53
V.A.G 1551 print-out Possible cause
Repair
01314
Engine control module
No communication
- Read measured value block
Page 01-61
display group
number 125
Open circuit, short to
positive or Ground in
data bus wiring
- Check wiring and connections
of data bus wiring using wiring
diagram
- Perform electrical checks
Page 01-102
01315
Transmission Control
Module (TCM)
1)
No communication
- Read measured value block
Page 01-61
display group
number 125
Open circuit, short to
positive or Ground in
data bus wiring
- Check wiring and connections
of data bus wiring using wiring
diagram
- Perform electrical checks
Page 01-102
1)
Vehicles with automatic transmission only.
ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст