Volkswagen Golf / Golf GTI / Jetta. Manual — part 197
24-42
Checking resistance
If the specification is not obtained:
If the specification is obtained:
- Check sensor heater wire
resistance at connector terminals
3 and 4 to Oxygen Sensor (O2S).
Specification: 2.5 to 10.0
(at
room temperature).
- Replace Oxygen Sensor (O2S) 1,
Bank 1 before Three Way
Catalytic Converter (TWC) -G39-
Page 24-19
, item 20 .
- Check DTC memory, repair
malfunctions if necessary and
then erase DTC memory
Page
01-23
.
- Erase learned values and adapt
Motronic Engine Control Module
(ECM) -J220- again
Page 24-
182
.
- Read readiness code
Page 01-
146
. If DTC memory has been
erased or Motronic Engine
Control Module (ECM) -J220- was
disconnected from battery
positive (B+), readiness code
must be generated again
Page
01-149
.
Components, checking
24-43
Checking voltage supply
If no voltage is present:
Repair Manual, Electrical
Equipment; Repair Group 92
- Connect multimeter to measure
voltage at terminals 3 and 4
(connector to Motronic Engine
Control Module (ECM) -J220-)
using adapter cables from VAG
1594.
- Start engine and run at idle
speed.
- Measure voltage supply and
observe display group 41, display
zone 2.
Display Htg.bC.ON: Specification:
11.0 to 14.5 V
Display Htg.bC.ON / Htg.bC.OFF
(alternating): Specification:
Between 0.0 to 12.0 V fluctuating
- Switch off ignition.
- Remove wiper arms and cowl
panel:
- Connect VAG 1598/31 test box to
control module wiring harness.
Engine Control Module (ECM) -
J220- remains disconnected.
Components, checking
24-44
If the specification is obtained:
If no wiring malfunction is detected:
- Check wiring for open circuit
between test box and 6-pin
connector according to Electrical
Wiring Diagrams. Terminal 4 and
socket 5
Wire resistance: max. 1.5
- Check wire for open circuit
between 6-pin connector terminal
3 and Fuel Pump (FP) -J17-
referring to Electrical Wiring
Diagrams.
Wire resistance: max. 1.5
- Replace Motronic Engine Control
Module (ECM) -J220-
Page 24-
173
.
- Check DTC memory, repair
malfunctions if necessary and
then erase DTC memory
Page
01-23
.
- Erase learned values and adapt
Motronic Engine Control Module
(ECM) -J220- again
Page 24-
182
.
- Read readiness code
Page 01-
146
. If DTC memory has been
erased or Motronic Engine
Control Module (ECM) -J220- was
disconnected from battery
positive (B+), readiness code
must be generated again
Page
01-149
.
Components, checking
24-45
Oxygen Sensor (O2S) heating for
Oxygen Sensor (O2S) Behind Three Way
Catalytic Converter (TWC) -G130-,
checking
Note:
The vehicle must be raised to gain access to
the Oxygen Sensor (O2S) connector.
Only gold plated terminals may be used when
servicing Oxygen Sensor (O2S) connector
terminals 3 and 4.
Special tools and equipment
Note:
All functions which could previously be performed
with VAG 1551/1552 can also be performed with
the VAS 5051.
VAG 1551 Scan tool (or VAG 1552) with VAG
1551/3 adapter cable
VAG 1526 or Fluke 83 Hand multimeter or VAG
1715 multimeter
VAG 1594 Adapter set
VAG 1598/31 Test box
Electrical Wiring Diagrams
Components, checking
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст