Volkswagen Golf / Golf GTI / Jetta. Manual — part 902
01-384
Installing
Note the polarity and correct position
when installing the batteries.
- Place the battery -4- with the
positive terminal downwards into
the sensor unit (positive terminal
is marked on housing).
- Now place the contact plate -3-
on the battery -4-.
- Place battery -2- with the positive
terminal downwards onto the
contact plate and secure.
- Place transmitter unit -1- and
transmitter unit -5- halves
together and clip to create one
remote transmitter assembly.
- Then engage the transmitter unit
with the main key.
Central locking system (vehicles without power windows), On Board Diagnostic ...
13/2/2005
01-385
Driver's side seat
adjustment, On Board
Diagnostic (OBD)
Seat adjustment, functional
description
The 8-way seat is equipped with a
seat and mirror memory function.
With this system individual seat and
mirror adjustments can be stored in
the memory. Each of the memory
buttons -1-, -2-, -3- can be used to
store the individual settings for one
person.
The seat and mirrors will move
automatically into the required
position by pressing the appropriate
button when there is a change of
driver.
In the driver's seat adjustment, the
position of the exterior mirrors (left
and right) when driving forward and
the position of the right exterior
mirror for reversing can be stored
and recalled for each memory button
-1-, -2-, -3-.
The adjustments stored on a
memory button can also be called up
using the key for the radio wave
remote control.
The memory system can be turned
off at any time using the red switch -
4- (MEM OFF). The seat and the
exterior mirrors can then only be set
manually with switches -5- and -6-.
Driver's side seat adjustment, On Board Diagnostic (OBD)
13/2/2005
01-386
On Board Diagnostic (OBD),
functional description
It is an independent system and has the On
Board Diagnostic (OBD) address word 36
"Seat adjustment driver's side".
The seat adjustment control module -J136-
is located under the driver's seat and is
connected to the convenience system via
the CAN data bus.
It is equipped with a DTC memory. The On
Board Diagnostic (OBD) connection is
located under the driver's knee bar to left of
the steering wheel.
The control module detects malfunctions in
the system and stores them in a permanent
memory.
To commence troubleshooting, initiate self-
diagnosis and retrieve the stored information
with the V.A.G 1551 scan tool.
V.A.G 1552 System tester may also be
used.
The malfunction information displayed is
used to refer to a DTC table with notes on
the possible causes for directed repair
measures.
Malfunctions which can be attributed to a
temporary open circuit in the wiring or a
loose contact, will also be stored. These
malfunctions will be displayed as sporadic
DTCs "SP".
The individual operating functions are
described in the following description.
Driver's side seat adjustment, On Board Diagnostic (OBD)
13/2/2005
01-387
Memory system, initializing
Note:
All data stored for the seat and mirror settings
will be lost when the vehicle battery is
disconnected.
This data will be retained in future control
modules even after the battery has been
disconnected.
Each new setting stored on the same button will
erase the previous data.
It is not possible to store settings on the
memory buttons if the red switch is switched-off
(switch protrudes).
The battery voltage must not be below 10.5 V.
Otherwise the system detects low voltage and
will store a malfunction in the DTC memory.
The following test steps must be performed for
the initialization:
- Open driver's door.
- Switch on ignition.
- Then move the seat backrest forwards as far as
stop.
This position will be recorded for reference when
the stop limit switch-off occurs.
Driver's side seat adjustment, On Board Diagnostic (OBD)
13/2/2005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст