Volkswagen Golf / Golf GTI / Jetta. Manual — part 146
01-163
- Check Oxygen Sensor (O2S) control status after
Three Way Catalytic Converter (TWC) (display
zone 2): Specification: 111
Significance of figures in 3 digit number block
Page 01-217
.
Note:
The bits in display zone 2 will not be set to 1 until
the Three Way Catalytic Converter (TWC)
temperature rises above 380 C (
display
groups 34, display zone 2).
If the specification is not obtained:
- Press
button.
- Check Oxygen Sensor (O2S) heater of Oxygen
Sensor (O2S) after Three Way Catalytic
Converter (TWC)
Page 24-45
.
If the specification is obtained:
- Press
button.
Work step 10: Oxygen Sensor (O2S) aging
diagnosis of Oxygen Sensor (O2S) after
Three Way Catalytic Converter (TWC)
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -4- for function "Initiate
basic setting" and confirm entry with -Q- button.
Readiness code
01-164
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -4- and -3- for
"Display group number 43" and
confirm entry with -Q- button.
System in basic setting 43
1
2
3
4
Indicated on display: (1 to 4
display zones)
Note:
This process can take approx. 30
seconds.
- Depress brake pedal and hold.
- Depress accelerator down to wide
open throttle position.
Engine speed will be increased by
Motronic Engine Control Module
(ECM) -J220- to approx. 2300
rpm.
- Depress and hold brake pedal
and accelerator until display in
display zone 4 jumps from "Test
OFF" to "Test ON", when
performing this test the Three
Way Catalytic Converter (TWC)
temperature in display zone 2
must be at least 380 C.
- Depress and hold brake pedal
and accelerator until display zone
4 displays specification "B1 P2
OK.".
- Release brake and accelerator
pedals.
Readiness code
01-165
If "B1 P2 n.OK." appears in display zone 4:
- Press
button.
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If no DTC is stored:
- Check aging of Oxygen Sensor (O2S) after
Three Way Catalytic Converter (TWC)
Page
24-154
.
If "B1 P2 OK." appears in display zone 4:
- Press -C- button.
Work step 11: Oxygen Sensor (O2S)
diagnosis after Three Way Catalytic
Converter (TWC) (operational readiness)
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -3- and -6- for "Display group
number 36" and confirm entry with -Q- button.
Readiness code
01-166
System in basic setting 36
1
2
Indicated on display: (1...2
display
zones)
If the diagnosis is initiated by the
Motronic Engine Control Module
(ECM) -J220- the display in display
zone 2 jumps from "Test OFF" to
"Test ON".
Note:
This process can take approx. 30
seconds.
If "B1 P2 n.OK." appears in display
zone 4:
- Leave engine running at idle until
display zone 2 shows
specification "B1 P2 OK.".
- Press
button.
- Check DTC memory, repair
Diagnostic Trouble Codes (DTCs)
if necessary and then erase DTC
memory
Page 01-23
, DTC
memory, checking and erasing.
- Read readiness code
Page 01-
146
. If the DTC memory has
been erased or the Motronic
Engine Control Module (ECM) -
J220- was disconnected from
battery (B+) positive, the
readiness code must be
generated again
Page 01-149
.
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст