Volkswagen Golf / Golf GTI / Jetta. Manual — part 145
01-159
Work step 7: Oxygen Sensor
(O2S) aging diagnosis of Oxygen
Sensor (O2S) before Three Way
Catalytic Converter (TWC)
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -4- for
function "Initiate basic setting"
and confirm entry with -Q- button.
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -0-, -3- and -4- for
"Display group number 34" and
confirm entry with -Q- button.
System in basic setting 34
1
2
3
4
Indicated on display: (1...4
display
zones)
- Depress brake pedal and hold.
- Depress accelerator down to wide
open throttle position.
Engine speed will be increased by
Motronic Engine Control Module
(ECM) -J220- to approx. 2300
rpm.
- Depress brake pedal and
accelerator down until display in
display zone 4 jumps from "Test
OFF" to "Test ON". When
performing this test Three Way
Catalytic Converter (TWC)
temperature in display zone 2
must be at least 380 C.
Readiness code
01-160
Note:
This process can take approx. 90 seconds.
- Depress brake pedal and accelerator down until
display zone 4 displays specification "B1-P1
OK.".
- Release brake and accelerator pedals.
If "B1 P1 n.OK." appears in display zone 4:
- Press
button.
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If no DTC is stored:
- Check aging of Oxygen Sensor (O2S) before
Three Way Catalytic Converter (TWC)
Page
24-150
.
If "B1 P1 OK." appears in display zone 4:
- Press C button.
Readiness code
01-161
Work step 8: Fuel supply system
diagnosis (part load)
Basic setting
Input display group number XXX
Indicated on display:
- Press buttons -2-, -1- and -6- for
"Display group number 216" and
confirm entry with -Q- button.
System in basic setting 216
1
2
3
4
Indicated on display: (1 to 4
display zones)
If the display does not indicate as
described:
- Depress brake pedal and hold.
- Depress accelerator down to wide
open throttle position.
Engine speed will be increased by
Motronic Engine Control Module
(ECM) -J220- to approx. 2300
rpm.
- Depress brake pedal and
accelerator down until display
zone 4 displays (after approx. 75
seconds) specification
"xxxxx100".
- Release brake and accelerator
pedals.
- Press
button.
Readiness code
01-162
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If the display indicates as described:
- Press
button.
Work step 9: Oxygen Sensor (O2S) control
diagnosis status after Three Way Catalytic
Converter (TWC)
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -8- for function "Read
measured value (data) block" and confirm entry
with -Q- button.
Read measured value block
Input display group number XXX
Indicated on display:
- Press buttons -0-, -3- and -0- for "Display group
number 30" and confirm entry with -Q- button.
Read measured value block 30
1
2
Indicated on display: (1...2
display zones)
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст