Volkswagen Golf / Golf GTI / Jetta. Manual — part 144
01-155
- Read Engine Coolant Temperature value in
display zone 3.
Specification: 85 to 110 C
- Read Intake Air Temperature value in display
zone 4.
Specification: Ambient temperature less than 80
C
If the specifications are obtained:
- Press
button.
Work step 5: Evaporative Emissions (EVAP)
Canister system diagnosis (Tank ventilation
system)
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -4- for function "Initiate
basic setting" and confirm entry with -Q- button.
Basic setting
Input display group number XXX
Indicated on display:
Note:
The engine must not be loaded during this
diagnosis, if this occurs the diagnosis will be
interrupted and will not start again until the engine
is revved-up.
- Press buttons -0-, -7- and -1- for "Display group
number 71" and confirm entry with -Q- button.
Readiness code
01-156
System in basic setting 71
1
2
3
4
Indicated on display: (1 to 4
display zones)
If "Reed op." appears in display zone
1:
If the diagnosis is initiated by the
Motronic Engine Control Module
(ECM) -J220- the display in display
zone 4 jumps from "Test OFF" to
"Test ON".
Note:
If the display in display zone 4 jumps
from "Test OFF" to "Test ON" during
the diagnosis, repeat the diagnosis
again. When repeating the
diagnosis, the diagnosis can take up
to 60 seconds before the display in
display zone 4 jumps from "Test
OFF" to "Test ON".
If "Sm leak or La leak" (meaning
Small leak or Large leak) appears in
display zone 2 and "Sys. n.OK."
appears in display zone 4:
- Open fuel tank filler cap briefly to
release pressure in fuel tank. This
will close reed terminal.
- Leave engine running at idle until
specification "Sys. OK." is
displayed in display zone 4.
- Press
button.
Readiness code
01-157
- Check DTC memory, repair Diagnostic Trouble
Codes (DTCs) if necessary and then erase DTC
memory
Page 01-23
, DTC memory, checking
and erasing.
- Read readiness code
Page 01-146
. If the
DTC memory has been erased or the Motronic
Engine Control Module (ECM) -J220- was
disconnected from battery (B+) positive, the
readiness code must be generated again
Page 01-149
.
If no DTC is stored:
- Check Evaporative Emissions (EVAP) Canister
system for leaks:
Repair Manual, 2.8 Liter VR6 4V Engine
Mechanical, Engine Code(s): BDF; Repair Group
20
If "Sys. OK." appears in display zone 4:
- Press
button.
Work step 6: Oxygen Sensor (O2S) control
diagnosis status before Three Way Catalytic
Converter (TWC)
Rapid data transfer
HELP
Select function XX
Indicated on display:
- Press buttons -0- and -8- for function "Read
measured value (data) block" and confirm entry
with -Q- button.
Read measured value block
Input display group number XXX
Indicated on display:
Readiness code
01-158
- Press buttons -0-, -3- and -0- for "Display group
number 30" and confirm entry with -Q- button.
Read measured value block 30
1
2
Indicated on display: (1 to 2
display zones)
Significance of figures in 3 digit number block
Page 01-217
.
Note:
The bits in display zones 1 will not be set to 1 until
the Three Way Catalytic Converter (TWC)
temperature rises above 380 C (
display groups
34, display zone 2).
If the specification is not obtained:
If the specification is obtained:
- Check Oxygen Sensor (O2S) control status
before Three Way Catalytic Converter (TWC)
(display zone 1):
Specification: 111
- Press
button.
- Check Oxygen Sensor (O2S) heater of Oxygen
Sensor (O2S) before Three Way Catalytic
Converter (TWC)
Page 24-38
.
- Press
button.
Readiness code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст