Volkswagen Golf / Golf GTI / Jetta. Manual — part 1038
01-64
Rapid data transfer
HELP
Select function XX
Indicated on display after completion
of automatic sequence:
- Press buttons -0- and -6- to select
function 06, "End Output".
Rapid data transfer
Q
06 - End Output
Indicated on display:
- Press -Q- button to confirm input.
Rapid data transfer
Help
Enter address word XX
Indicated on display:
Note:
After completion of the automatic
sequence, the instrument cluster
must be briefly disconnected from
voltage supply terminal 30 to allow
the clock correction to take effect.
The clock correction takes effect
after reconnecting the instrument
cluster to voltage supply terminal
30.
The digital clock accuracy is now
corrected.
- Switch off ignition.
- Disconnect VAG 1551 scan tool
from Data Link Connector (DLC).
- Switch off ignition.
- Remove Fuse No. 15 (5 A) from
fuse holder, wait at least 10
seconds, and reinsert fuse.
Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)
13/2/2005
01-65
Instrument cluster m.y.
2000 through m.y. 2001, On
Board Diagnostic (OBD)
General information
The instrument cluster contains an electronic
speedometer, tachometer, liquid crystal
(LCD) displays for odometer, trip
odometer/clock, as well as analog coolant
temperature and fuel level gauges. Control
and warning lamps are situated within and
between the speedometer and tachometer.
Automatic transmission models also contain
an LCD gear indicator display.
Where available, an LCD multi-function trip
computer (MFI) with two operating modes is
located in the tachometer display. The MFI
includes selectable displays for trip
time/mileage, average trip speed, average
trip fuel consumption and outside
temperature.
The instrument cluster is controlled by an
internal microprocessor with On Board
Diagnostic (OBD) capability. If malfunctions
occur in monitored sensors and
components, Diagnostic Trouble Codes
(DTC) will be stored in memory together with
an indication of malfunction type. A
maximum of 4 DTCs can be stored
simultaneously.
Sporadic malfunctions (indicated in the
readout by "SP") are automatically cancelled
if not repeated in the next 50 engine starts.
Instrument clusters from m.y. 2000 are
integrated into the "Powertrain" CAN Data
Bus network (may also be known as "CAN-
Bus" or "Data-Bus").
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
01-66
The Data Bus On Board Diagnostic Interface -
J533- (which is integrated into the instrument
cluster) enables data to be exchanged between
the "Powertrain" CAN Data-Bus network and the
Data Link Connector (DLC) "K-wire".
The Data Bus On Board Diagnostic Interface -
J533- has specific On Board Diagnostic (OBD)
capabilities.
Before performing any troubleshooting or
inspection, always begin by checking for DTCs
using the OBD program. DTCs stored in memory
are retrieved/checked with either the VAG
1551/1552 Scan Tool (ST) or VAS 5051 Vehicle
Diagnostic Tester.
Notes on exchanging instrument cluster
Do not disassemble instrument cluster.
Instrument clusters contain no field serviceable
components. All malfunctions require
replacement of instrument cluster.
When the replacement of a malfunctioning
instrument cluster is necessary, follow
exchange part procedures.
Complete the report form and return together
with instrument cluster.
Use the original packaging from the new cluster
when returning modules.
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
01-67
Replacement instrument clusters must be
coded according to vehicle market version and
equipment level variables using the OBD
program
Vehicles 05.99 05.00
Page 01-95
Vehicles 05.00
Page 01-99
Replacement instrument clusters must be
adapted for anti-theft immobilizer function
table of contents for specific applications.
The Data Bus On Board Diagnostic Interface -
J533- must be coded depending on the vehicle
equipment when replacing the instrument
cluster
Page 01-136
.
Additional information:
Complaint/symptom based Technical Bulletins
("Service Fixes"):
Technical Bulletins
Instrument cluster
Repair Manual, Electrical
Equipment, Repair Group 90
.
Instrument cluster m.y. 2000 through m.y. 2001, On Board Diagnostic (OBD)
13/2/2005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст