Volkswagen Golf / Golf GTI / Jetta. Manual — part 1037

01-60

Channel 03 Adaptation 90

Changed value is stored

Indicated on display:

- End consumption indicator

adaptation with

button.

Rapid data transfer

HELP

Select function XX

Indicated on display:

Note:

A false entry switches the tester to
"Select function" mode.

Function is unknown or

cannot be carried out at the moment

If the following display appears:

- Press

button.

- Select function "10 - Adaptation"

and adaptation channel 03 again.

- Carry out corrections to

consumption indicator and
confirm with Q button.

Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)

13/2/2005

01-61

Digital clock (Motometer - where
applicable), correction

Notes:

Correction of the clock is only possible with

Motometer instrument clusters from a limited
manufacturing period.

Scan tool VAG 1551 with a program card

version /8.0 is required for clock correction.

The digital clock in the instrument cluster may
deviate from the correct time by a maximum of 5
seconds within 24 hours

If the deviation is greater than 5 seconds:

- Check control module version

Page 01

1J0919861D A4 KOMBIINSTR. VDO V02

Coding 00042

WSC 00000

If indicated on display (example only): VDO

instrument cluster - replace instrument cluster
(digital clock cannot be corrected).

1J0919861D KOMBI + WEGFAHRSP. MMO V02

Coding 00042

WSC 00000

If indicated on display (example only): Motometer

instrument cluster.

- First check VAG program card version, then

check if the digital clock can be corrected:

Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)

13/2/2005

01-62

VAG 1551 program card version,
checking

- Press

button.

Rapid data transfer

HELP

Select function XX

Indicated on display:

- Press buttons -0- and -6- to select

function 06, "End Output".

Rapid data transfer

Q

06 - End Output

Indicated on display:

- Press -Q- button to confirm input.

Rapid data transfer

HELP

Enter address word XX

Indicated on display:

After approx. 5 seconds:

- Switch off ignition.

- Disconnect VAG 1551 scan tool

from Data Link Connector (DLC).

- Connect cable VAG 1551/3C to

DLC again.

VAG 1551 -D / 8.0- 1.10.1998

The VAG 1551 display will show

program card version , language and
edition date for approx. 3 seconds:

If the display of the VAG 1551 does
not indicate program card
version /8.0:

If the display of the VAG 1551
indicates program card version /8.0
or /9.0, proceed as follows:

- Obtain program card version / 9.0

and insert into VAG 1551.

Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)

13/2/2005

01-63

Digital clock, initiate correction

Notes:

The digital clock accuracy can only be adapted

with a VAG 1551in conjunction with program
card /8.0 or /9.0.

The VAG 1551 recognizes instrument cluster

versions where clock correction is possible.

- Select operating mode 1 "Rapid data transfer",

switch on ignition and enter address word 17
"Instrument cluster".

- Press -Q- button to confirm input.

- Press

button until "Select function"appears in

display.

Rapid data transfer

HELP

Select function XX

Indicated on display:

When the VAG 1551 recognizes a instrument
cluster without digital clock correction cpabilities,
"function 12" cannot be selected. In these cases,
replace instrument cluster.

- Press buttons -1- and -2- to select function 12

"Clock correction".

Rapid data transfer

Q

12 - Clock correction

Indicated on display:

The VAG 1551 initiates and automatic sequence
after pressing the -Q- button.

- Press -Q- button to confirm input.

Rapid data transfer

Clock correction

Indicated on display during automatic sequence.

Instrument cluster through m.y. 1999, On Board Diagnostic (OBD)

13/2/2005