Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 813
1 - Counter Hold - VAS6779/7-
2 - Funnel - VAS6779/6- , -arrow marking- on the Funnel -
VAS6779/6- must align in the center of both bolts -arrow-.
3 - Thrust Piece - VAS6779/9-
4 - Incremental Ring - VAS6779/8- , the marking -I- on the Incre‐
mental Ring - VAS6779/8- must align with the marking -X- on the
Thrust Piece - VAS6779/9-
5 - Hydraulic Press - VAS6178- with Bearing Installer - Wheel
Hub/Bearing Kit Pressure Head - T10205/13-
6 - Hexagon Nut - VAS6779/3-
7 - Threaded Rod - VAS6779/2-
– Press in both bonded rubber bushing at the same time.
– Remove Hydraulic Press - Bushing Tool Kit - VAS6779- from
the subframe and check seating of the pressed in bonded rub‐
ber bushing.
– Fasten the stabilizer bar with the subframe and the coupling
rod.
– Install the pendulum support. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe Mount;
Pendulum Support, Removing and Installing or ⇒ Engine Me‐
chanical, Fuel Injection and Glow Plug; Rep. Gr. 10 ; Sub‐
frame Mount; Pendulum Support, Removing and Installing .
– Install the front noise insulation. Refer to ⇒ Body Exterior;
Rep. Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Subframe”, page 16
♦ Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition;
Rep. Gr. 10 ; Subframe Mount; Overview - Subframe Mount
or ⇒ Engine Mechanical, Fuel Injection and Glow Plug; Rep.
Gr. 10 ; Subframe Mount; Overview - Subframe Mount
♦ Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Noise Insulation;
Overview - Noise Insulation .
2.7
Stabilizer Bar, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Engine and Gearbox Jack - VAS6931-
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheels.
– Remove the lower noise insulation. Refer to ⇒ Body Exterior;
Rep. Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the exhaust system bracket from the subframe
-arrows-.
– Remove the pendulum support bolts -1-.
– Remove the hex nut -1- from the right and left coupling rod
-3-.
– Remove the coupling rod -3- from the stabilizer bar -2- on the
left and right sides.
– Remove the nuts -arrows- on the left and right side of the ve‐
hicle.
Vehicles with Level Control System Sensor
– Disconnect the connector -1- from the Left Front Level Control
System Sensor - G78- or Right Front Level Control Sensor -
G289- .
– Remove the nut -1-.
– Remove the bracket -2- for the Left Front Level Control System
Sensor - G78- or Right Front Level Control Sensor - G289-
from the control arm -3-.
– Remove the bolt -1-.
– Remove the Left Front Level Control System Sensor - G78-
-2- or Right Front Level Control Sensor - G289-
Continuation for all Vehicles.
– Remove the clips -1 and 2- for the wiring harness -3- from the
subframe and the steering gear.
– Remove the stabilizer bar bolts -1-.
– Remove the steering gear bolts -1-.
– Pry the steering gear out of the subframe alignment sleeves.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст