Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 569
Check the Ends of the Diaphragm Spring
• Wear up to half the thickness of the diaphragm spring
-arrows- is permitted.
Note
Allocate clutch pressure plate and clutch plate according to the
engine code. Refer to the Parts Catalog.
Checking the Pull-Springs and Rivet Connection
I - Pull-spring OK
• Slight offset in the outer area -arrows A-.
II - Pull-springs damaged
• The clutch pressure plates must be replaced if the pull-spring
is bent or broken off -arrow B-.
Checking the Spring Connections and Rivet Connections
– Make sure the rivet connections -arrows B- fit correctly on all
pull-springs -arrows A-.
• Replace any clutch pressure plates that have loose rivet con‐
nections -arrows B-.
Only Check Position of Adjustment Mechanism with New Pres‐
sure Plates
• Both edges -A- of the adjusting ring must be located between
both notches -arrows B-.
• If the adjusting ring takes on a different position with new pres‐
sure plates, pressure plate and clutch plate must not be in‐
stalled.
• With used clutches, the adjusting ring may take on a position
outside of the notches.
– Install the Flywheel Retainer - 3067- .
– Install the clutch pressure plate on the centering pins.
– Center the clutch plate with the Alignment Tool - Clutch Plate
- 3190A- .
When Installing, Tighten Bolts as Follows So Clutch Pressure
Plate Does Not Distort (Causing Shuddering On Acceleration):
– Install all bolts evenly, by hand, until the bolt heads touch the
clutch pressure plate.
– Tighten the bolts diagonally in small steps.
– Install the transmission. Refer to
⇒ “2.2 Transmission, Installing”, page 77
Tightening Specifications
♦ Pressure plate on the flywheel. Refer to
⇒ “2.1.2 Overview - Clutch, with Dual Mass Flywheel, LuK”,
2.2.3
Clutch, Removing and Installing, with
Single Flywheel
Special tools and workshop equipment required
♦ Flywheel Retainer - 3067-
♦ Alignment Tool - Clutch Plate - 3190A-
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Grease for Clutch Disc Shaft Splines - G 000 100-
Removing
• The transmission is removed.
– Insert the Flywheel Retainer - 3067- to loosen the bolts.
When Removing, Loosen the Bolts as Follows So That the Clutch
Pressure Plate Does Not Distort (Causing Shuddering on Accel‐
eration):
– Loosen the bolt diagonally in small steps.
– Remove the pressure plate and the clutch plate.
Installing
Note
♦
Allocate clutch pressure plate and clutch plate according to the
engine code. Refer to the Parts Catalog.
♦
Clean the input shaft splines and (on used clutch plates) the
hub splines. Remove any corrosion and then apply a very thin
coat of Grease for Clutch Disc Shaft Splines - G 000 100- on
the splines. Then move the clutch plate back and forth on the
input shaft until the hub moves freely on the shaft. Remove
any excess grease.
♦
The clutch pressure plates are corrosion-protected and
greased. With the exception of the friction surface on the clutch
plate, do not clean the clutch pressure plate. This will shorten
the service life of the clutch considerably.
♦
The friction surfaces on the clutch pressure plate and on the
flywheel must be cleaned thoroughly (degreased).
♦
To reduce odor caused by a burnt clutch, thoroughly clean the
clutch housing, the flywheel and the side of the engine facing
toward the transmission.
♦
Only use compressed air to clean the dual mass flywheel.
♦
The clutch plate linings must sit completely on the flywheel and
on the clutch pressure plate friction surface. Install the bolts.
♦
Tighten the bolts diagonally in small steps so as to not damage
the centering holes in the pressure plate and the centering pins
on the flywheel.
♦
Make sure the alignment sleeves for centering the engine/
transmission are installed inside the cylinder block. Install
them if necessary.
♦
If the alignment sleeves are missing, it will be difficult to shift,
there will be clutch problems and the transmission may make
noises (loose rattling).
• Clutch plate installed location: The labeling
“Getriebeseite” (transmission side) or the shorter end of the
hub with the spring cage faces the pressure plate.
Check the Ends of the Diaphragm Spring
• Wear up to half the thickness of the diaphragm spring
-arrows- is permitted.
Check the Spring Connection and Rivet Connections
– Check the spring connection between the pressure plate and
the cover for cracks and make sure the rivet connections are
tight.
– Replace the pressure plate if the springs are damaged or if the
rivet connections -arrows- are loose.
Checking the Pull-Springs and Rivet Connection
I - Pull-spring OK
• Slight offset in the outer area -arrows A-.
II - Pull-springs damaged
• The clutch pressure plates must be replaced if the pull-spring
is bent or broken off -arrow B-.
– Check the spring connections -arrows A- for damage and
make sure the rivet connections -arrows B- are tight.
• Replace a clutch pressure plate with severely kinked or broken
spring connections and loose rivet connections.
– Make sure the rivet connections -arrows B- fit correctly on all
pull-springs -arrows A-.
• Replace any clutch pressure plates that have loose rivet con‐
nections -arrow B-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст