Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 426
Caution
Risk of damage to the bushing -1- in the bearing point -2- (ad‐
justing spindle/seat pan bolting).
♦ The bushing cannot be replaced with workshop materials.
♦ If the bushing is damaged, the corresponding assembly
parts must be replaced.
– Disconnect the connector -3- at the seat angle adjustment
motor.
– Remove the bolts -1- and the seat angle adjustment motor
-4-.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “2.7 Overview - Seat Angle Adjuster”, page 333
2.18
Seat Height Adjustment Handle, Re‐
moving and Installing
Note
The seat height adjustment handle can only be replaced with the
front seat installed.
Removing
Note
♦
Remove the seat height adjustment handle as described. Nev‐
er drive the seat height adjustment handle off the lever.
♦
If the tab gets damaged while removing the handle, then it is
not possible to install it again. The handle must be replaced.
– Pull the seat height adjustment handle in direction of -1- as far
upward as possible and hold it in that position.
– Guide a small screwdriver up to the retainer -3- between the
seat height adjuster handle -1- and the trim -2-.
– Press the retaining tab -3- inward using the screwdriver.
– At the same time, remove the seat height adjuster handle -1-
from the lever -4- in the direction of the -arrow-.
Installing
Install in reverse order of removal while paying attention to the
following:
– Check for damage and proper seating of the retainer -3- on
the lever -4-.
– Slide the seat height adjustment handle -1- onto the lever -4-
until it engages.
– After installing, make sure the retainer -4- is properly engaged.
– Check for secure fit by pulling on it.
2.19
Seat Height Adjuster, Removing and In‐
stalling
⇒ “2.19.1 Seat Height Adjuster, Removing and Installing, Except
Power Seat”, page 353
⇒ “2.19.2 Seat Height Adjuster, Removing and Installing, Power
2.19.1
Seat Height Adjuster, Removing and In‐
stalling, Except Power Seat
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Position the seat into its highest position.
– Remove the backrest adjuster. Refer to
⇒ “2.21.1 Backrest Adjuster, Removing and Installing, Except
– Remove the seat height adjustment handle. Refer to
⇒ “2.18 Seat Height Adjustment Handle, Removing and In‐
.
– Remove the sill-side seat trim. Refer to
⇒ “2.14.1 Door Sill Side Seat Trim, Removing and Installing,
.
– Remove the bolts -2-.
– Remove the lever -1-.
– Remove the lock washer -1-.
– Remove the bolts -1 and 3-.
– Remove the seat height adjuster -2-.
Installing
Install in reverse order of removal while paying attention to the
following:
Note
♦
The bolts -1- and the bolt -3- are different lengths.
♦
The bolt -3- is shorter.
♦
The bolt -3- has a larger bolt head.
♦
Ensure the correct allocation.
– Push the seat downward via the backrest.
– Attach the seat height adjuster -2-.
– Tighten the bolts -1 and 3-.
Tightening Specifications
♦ Refer to
⇒ “2.6.1 Overview - Seat Height Adjuster, Except Power Seat”,
2.19.2
Seat Height Adjuster, Removing and In‐
stalling, Power Seat
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
.
– Attach the front seat to the Fixture For Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
– Remove the sill-side seat trim. Refer to
⇒ “2.14.2 Door Sill Side Seat Trim, Removing and Installing,
– Disconnect the connector -1- at seat height adjustment motor
-2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст