Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 425
– Press the clamping pin -3- toward the inside.
– Pry off the expanding rivet -2- using the Trim Removal Wedge
- 3409- .
– Open the bracket -4- on the trim panel -1- from below.
– Guide out the rear trim panel -1-.
– Remove the trim panel -1- forward from the bracket -5-.
– Disconnect the connectors to the controls.
Installing
Install in reverse order of removal.
2.15
Seat Trim Bracket, Removing and In‐
stalling
⇒ “2.15.1 Seat Trim Bracket, Removing and Installing, Except
Power Seat”, page 348
⇒ “2.15.2 Seat Trim Bracket, Removing and Installing, Power
2.15.1
Seat Trim Bracket, Removing and In‐
stalling, Except Power Seat
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Position the seat into its highest position.
– Remove the sill-side seat trim. Refer to
⇒ “2.14.1 Door Sill Side Seat Trim, Removing and Installing,
.
– Remove the bolts -2-.
– Guide the retaining bracket -1- out of the mount -arrow- on the
storage compartment -3-, if necessary.
– Remove the retaining bracket -1- from the front seat.
Installing
Install in reverse order of removal while paying attention to the
following:
– If equipped, make sure the retaining bracket is seated cor‐
rectly in the storage compartment mount.
Tightening Specifications
♦ Refer to
2.15.2
Seat Trim Bracket, Removing and In‐
stalling, Power Seat
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Position the seat into its highest position.
– Remove the sill-side seat trim. Refer to
⇒ “2.14.2 Door Sill Side Seat Trim, Removing and Installing,
– Remove the bolts -2 and 3-.
Note
If necessary, carefully push the seat cover near the bolt -3- to the
side in order to remove the bolt -3-.
– Remove the retaining bracket -1- from the front seat.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “2.5.2 Overview - Seat Pan, Power”, page 328
2.16
Front Backrest, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Screws for backrest
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
– Secure the seat on the Fixture for Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
.
– Remove the tunnel side seat trim. Refer to
⇒ “2.13 Tunnel-Side Seat Trim, Removing and Installing”,
– Remove the sill-side seat trim. Refer to
⇒ “2.14 Sill-Side Seat Trim, Removing and Installing”,
– Disconnect the connectors from the backrest wiring harness.
– Unclip the clips -2 and 5- from the wiring harness -1- on the
seat pan.
– Loosen the wiring harness -1- with the mesh hose from the
seat pan.
– To do so, loosen all cable ties -3 and 4-.
The wiring harness between the connector station and the side
airbag is continuous.
– Guide the wiring harness to the side airbag out of the mesh
hose.
– To do so, loosen the cable ties -3 and 4-.
Only for Vehicles with Entry Assistance
– Disengage the release cable bracket -3 and 4- for entry as‐
sistance from the bracket on the seat pan.
– Disengage the release cable -1 and 2- for entry assistance
from the seat rail release.
– Disengage the bracket -5- for the release cable from the seat
rail.
Continuation for All Vehicles
– Remove the bolts -2-.
– Tilt the backrest -3- forward onto the seat pan -1-.
– Move the seat pan cushion to the side.
– Carefully remove the wiring harness for the side airbag -4-
from the seat pan.
– Remove the backrest.
Installing
Install in reverse order of removal while paying attention to the
following:
– Replace the damaged cable ties and clips.
– Route the wires in their original locations.
Tightening Specifications
♦ Refer to
⇒ “2.2 Overview - Front Seat”, page 318
♦ Refer to
⇒ “2.5 Overview - Seat Pan”, page 327
♦ Refer to
⇒ “2.4 Overview - Front Backrest”, page 323
2.17
Seat Angle Adjuster, Removing and In‐
stalling
Note
The following describes the removing and installing on the left
side of the vehicle. Removing and installing on the right side is
identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
.
– Attach the front seat to the Fixture For Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
– Remove bolt -2- for seat angle adjustment motor (preset by
the manufacturer) adjusting spindle -1-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст